Echo CS-4010 Скачать руководство пользователя страница 2

Страница: 2 / 60

TABLE OF CONTENTS

CS-4010

X7503380000

7/22 ECHO Incorporated

TABLE OF CONTENTS

Introduction ................................................................................................. 4
Servicing Information .................................................................................. 4

Parts and Serial Number......................................................................  4
Service.................................................................................................  5
ECHO Consumer Product Support ......................................................  5
Product Registration ............................................................................  5
Additional Literature.............................................................................  5

Safety.......................................................................................................... 5

Manual Safety Symbols and Important Information .............................  5
International Symbols ..........................................................................  6
Personal Condition and Safety Equipment ..........................................  8
Rules for Safe Operation ...................................................................  12
Correct Use of Chain Brake...............................................................  14

Emission Control (Exhaust & Evaporative) .............................................. 20

CARB and EPA Emissions Control Information ................................. 20

Description ................................................................................................  21
Contents....................................................................................................  23
Assembly...................................................................................................  23

Preparation For Use........................................................................... 23

Operation .................................................................................................. 27

Содержание CS-4010





























































Результаты поиска

Содержание CS-4010

Отзывы:

Бренды по названию

Популярные бренды

Echo CS-4010, Руководство оператора

Результаты поиска

Содержание CS-4010

Отзывы:

Бренды по названию

Популярные бренды