manualshive.com logo in svg

Echo CS-4010, Руководство оператора

Поделиться
Скачать
Echo CS-4010 Скачать руководство пользователя страница 34

OPERATION

CS-4010

34

X7503380000

7/22 ECHO Incorporated

Note:  Do not increase engine speed while chain brake is locked. 

Severe brake damage will result.

Running

The saw chain should not move at idle, otherwise serious 
personal injury may result.

Note:  If saw chain moves adjust carburetor according to 

“Carburetor Adjustment” instructions in this manual, or see 

your dealer.

1.

After engine starts, allow it to 

return to idle and warm up before 

using.

2.

Move chain brake lever fully 

REARWARD to UNLOCK chain 

brake.

3.

Squeeze throttle trigger (A) 

gradually and increase engine 

speed.

4.

The chain starts running when 

the engine reaches clutch 

engagement speed (see 

technical data page).

5.

Confirm proper acceleration and 

lubrication of chain and bar.

6.

Do not run the engine at high 

speed unnecessarily.

7.

Be sure that saw chain stops moving when throttle trigger is released.

Unlock Chain brake

A

Содержание CS-4010





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды