Echo CS-4010 страница 55 Скачать руководство пользователя

Страница: 55 / 60

CS-4010

STORAGE

X7503380000

7/22 ECHO Incorporated

STORAGE

Storage After Use

Momentary STOP Switch automatically returns to RUN position.
Engine can start unintentionally. Always remove spark plug
lead from spark plug before assembling or performing
maintenance procedures. Serious personal injury can result.

• Inspect and adjust every part of the chain saw.

• Completely clean every part and repair if necessary.
• Apply thin coating of oil on metal parts to prevent rust.

• Remove chain and guide bar.

• Drain fuel tank completely. Press purge bulb 6-7 times to remove

remaining fuel from carburetor then drain the tank again. Close choke,

start and run the engine until it stops due to lack of fuel.

• Allow engine to cool. Remove the spark plug lead from the spark plug.

Remove the spark plug. Pour 7 cc (0.25 oz.) of fresh, clean, two-stroke

engine oil into the cylinder through the spark plug hole.

• Store in a dry area, free from dust.

Do not store in an enclosure where fuel fumes may accumulate
or reach an open flame or spark.

Do not lend or rent your chain saw without the Operator’s
Manual.

Note:

• For future reference, you should keep this Operator’s Manual.
• If this Operator’s Manual becomes illegible or is lost, please contact

your ECHO dealer, or go to www.echo-usa.com.

Содержание CS-4010





























































Результаты поиска

Содержание CS-4010

Отзывы:

Похожие инструкции для CS-4010

Бренды по названию

Популярные бренды

Echo CS-4010, Руководство оператора

Результаты поиска

Содержание CS-4010

Отзывы:

Похожие инструкции для CS-4010

Бренды по названию

Популярные бренды