Echo CS-4010 страница 52 Скачать руководство пользователя

Страница: 52 / 60

MAINTENANCE

CS-4010

X7503380000

7/22 ECHO Incorporated

• Be sure 1/5th of the file diameter

remains above cutter edge.

• Be sure to round off the front edge

of the depth gauge.

• Properly filed cutters are

shown in illustration.

• When setting of the chain is

finished, soak it in oil and

wash away filings completely

before using.

• When chain has been filed on

the bar, supply sufficient oil to

it, move the chain slowly to

wash away the filings before

using again.

• If the chain saw is operated

with filings clogged in the

groove, the saw chain and the

guide bar will be damaged

prematurely.

• If the saw chain becomes

soiled with resin, for instance,

clean it with kerosene and

soak in it oil.

To sharpen other chains, follow chain manufacturer’s instructions.

1/5th

80°

Side plate angle

30°

Top plate
filing angle

0.64 mm (0.025 in.)

Parallel depth gauge

Содержание CS-4010





























































Результаты поиска

Содержание CS-4010

Отзывы:

Похожие инструкции для CS-4010

Бренды по названию

Популярные бренды

Echo CS-4010, Руководство оператора

Результаты поиска

Содержание CS-4010

Отзывы:

Похожие инструкции для CS-4010

Бренды по названию

Популярные бренды