Echo CS-4010 Скачать руководство пользователя

Страница: 32 / 60

OPERATION

CS-4010

X7503380000

7/22 ECHO Incorporated

Move chain brake lever fully

FORWARD to LOCK chain brake

before starting.

Fill fuel tank with fuel mixture. Do

not over fill.

Fill chain oil tank with lubricant.

Do not over fill.

Push purge pump (A) 3 to 5

times or until fuel is visible in

purge pump.

Pull choke control knob (B) all the

way OUT (CLOSED [

] choke

position).

◆

After choke control knob is pulled and then knob is
returned to original position, throttle remains slightly open
(fast idle latch condition).

◆

Chain will attempt to move when engine is started with fast
idle throttle latch engaged.

◆

Do not start engine before chain brake is locked.

Securely hold the chain saw and pull starter handle several times until

first starting sound.

Push choke control knob (B) all the way IN (OPEN

choke position).

Pull starter handle to start the

engine.

Note: Do not pull starter rope out to

maximum possible position.

Note: Do not allow recoil handle to

snap back against the

casing.

Note: If engine does not start after

5 pulls, repeat instructions.

Chain Brake Locked

Содержание CS-4010





























































Результаты поиска

Содержание CS-4010

Отзывы:

Похожие инструкции для CS-4010

Бренды по названию

Популярные бренды

Echo CS-4010, Руководство оператора

Результаты поиска

Содержание CS-4010

Отзывы:

Похожие инструкции для CS-4010

Бренды по названию

Популярные бренды