background image

OPERATION

CS-4010

30

X7503380000

7/22 ECHO Incorporated

Spilled fuel is a leading cause of hydrocarbon emissions. Some 
locations may require the use of automatic fuel shut-off containers to 
reduce fuel spillage.

Storage

 - Fuel storage laws vary by locality. Contact your local government 

for the laws affecting your area. As a precaution, store fuel in an approved, 

airtight container. Store in a well-ventilated, unoccupied building, away from 

sparks and flames.

• Empty the fuel tank prior to storing the unit. Return unused fuel to an 

approved fuel storage container.

Stored two-stroke fuel can separate. ALWAYS shake fuel container 
thoroughly before each use.

Used oil and gasoline, and soiled towels are hazardous waste 
materials. Disposal laws vary by locality.

Units equipped with a momentary STOP Switch automatically 
return to RUN position. Engine can start unintentionally. Always 
remove spark plug lead from spark plug before assembling or 
performing maintenance procedures, otherwise, serious 
personal injury can result.

Servicing Fuel and Oil

When the fuel tank cap or oil tank cap 

is difficult to remove, remove the 

spark plug lead, pull the starter 

handle slowly, and use the starter 

handle to assist in removal of the cap.

Note: Not all caps include this 

feature.  

Chain Lubricant

Note:  Cap indication - Fuel/oil tanks are indicated by the following 

illustrations

Содержание CS-4010





























































Отзывы: