Echo CS-4010 страница 37 Скачать руководство пользователя | Manualshive

Страница: 37 / 60

background image

CS-4010

OPERATION

X7503380000

37

7/22 ECHO Incorporated

Start the engine, see that it is

running properly. Squeeze the

trigger to open the throttle wide

open and start the cut. If the chain is

properly sharpened, the cutting

should be relatively effortless. It is

not necessary to press down hard to

make the saw cut. Pushing the saw

too hard will slow the engine and

cutting will actually be more difficult.

Sap from palm trees may corrode metal parts unless proper saw
maintenance is performed. Make sure to clean metal parts from palm
sap immediately after use.

• Remove sprocket guard. Clean wood chips and sawdust from guard and

engine crankcase.

• Never use metal tools for cleaning which can scratch the metal paint and

allow corrosion to develop.

• Clean sap accumulation from metal parts with cloth and warm water with

soap.

• Rinse with clean water and dry metal surfaces.

• Apply a light coating of engine or bar and chain oil to metal parts after

they are cleaned.

• Install and properly tension guide bar and chain. Run engine for one

minute alternating engine speed between full throttle for five seconds and

idle for five seconds to coat metal parts with additional protective chain

oil.

◆

Do not run a chainsaw not under cutting load at wide open
throttle longer than five seconds or engine damage can
occur.

◆

Keep chain properly tensioned during operation to prevent
the chain from jumping out of the guide bar rail slot and
damaging metal engine parts.

«
...
35
36
37
38
39
...
»

Содержание CS-4010





























































Отзывы:

Нет отзывов

Похожие инструкции для CS-4010

Бренд: Eckman Страницы: 12

Бренд: Stanley Страницы: 32

Бренд: DuroStar Страницы: 24

Бренд: TitanTec Страницы: 20

Бренд: ICFR Страницы: 64

Бренд: Jonsered Страницы: 92

Бренд: EMAK Страницы: 122

Бренд: Yard Machines Страницы: 64

Бренд: Poulan Pro Страницы: 2

Бренд: Poulan Pro Страницы: 2

Бренд: Poulan Pro Страницы: 8

3400 Conter-Vibe

Бренд: Poulan Pro Страницы: 16

Бренд: Poulan Pro Страницы: 18

POWERPLUS POWXG1045

Бренд: VARO Страницы: 14

Бренд: Makita Страницы: 34

Бренд: Nakayama Страницы: 26

TB5018CC, TB5020CC

Бренд: Troy-Bilt Страницы: 48

Бренд: Troy-Bilt Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды