manualshive.com logo in svg

Echo CS-4010, Руководство оператора

Поделиться
Скачать
Echo CS-4010 Скачать руководство пользователя страница 31

CS-4010

OPERATION

X7503380000

31

7/22 ECHO Incorporated

Proper lubrication of the chain while in operation reduces friction between 

the chain and the guide bar to a minimum and assures a longer service life.

• Use bar and chain oil of high 

quality for this purpose.

• Do not use used or reclaimed oil 

to avoid various oiler problems.

• Use high quality bar and chain oil.

• Use bar and chain oil of the 

following grades: 

• SAE No. 30....in summer
• SAE No. 10....in winter or when cutting resinous trees.

• When refueling, also refill chain oil.

Winter Operation

Air cleaner cover - Use winter plug 

(A) to prevent carburetor trouble in 

winter.

• Remove air cleaner cover. Remove 

winter plug (A) from warm weather 

position (B), and install into cold 

weather position (C).

Note:  For operation at normal 

temperature (5°C [41°F]) 

return plug to its original 

position. To prevent over 

heating of the engine.

Starting Cold Engine

Make sure the bar and chain are free from any obstruction when 
starting the chain saw. 

Oil tank cap

Fuel tank cap

A

B

C

Содержание CS-4010





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды