manualshive.com logo in svg

Echo CS-4010, Руководство оператора

Поделиться
Скачать
Echo CS-4010 Скачать руководство пользователя страница 20

EMISSION CONTROL

CS-4010

20

X7503380000

7/22 ECHO Incorporated

EMISSION CONTROL (EXHAUST & 
EVAPORATIVE)

CARB and EPA Emissions Control Information

The emission control system for 

the engine is EM (engine 

modification) and, if the second to 

last character of the Engine Family 

on the Emission Control 

Information label (sample below) is 

“B”, “C”, “K”, or “T”, the emission 

control system is EM and TWC 

(3-way catalyst). The fuel tank/fuel 

line emission control system is EVAP (evaporative emissions). Evaporative 

emissions for California models are only applicable to fuel tanks and fuel 

feed lines.

An Emission Control Label

 is 

located on the engine. (This is an 

EXAMPLE ONLY, information on 

label varies by engine FAMILY).

Product Emission Durability (Emission Compliance Period)

The 50 or 300 hour emission compliance period is the time span selected by 

the manufacturer certifying the engine emissions output meets applicable 

emissions regulations, provided that approved maintenance procedures are 

followed as listed in the Maintenance Section of this manual.

Содержание CS-4010





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды