background image

64

S611 Soft Starter

    MN03902011E—May 2012    www.eaton.com

Appendix E—Special Function Option

Pump Control Option

This option is intended to reduce the potential for water 
hammer in a centrifugal pump system by using a starting and 
stopping algorithm developed for pump control. Upon a start 
command, the speed of the motor is increased, under the 
control of the S611 soft starter microprocessor, to achieve a 
gentle start. After the speed has reached its nominal value, 
the bypass contactors close and the pump operates as with 
any other starter. Upon a stop command, the bypass 
contactors are opened and the motor speed is decreased in a 
tapered manner, to gradually slow the flow until the motor is 
brought to a stop. The start and stop ramp times are user 
adjustable and are to be set for the application requirements.

The pump control option is a factory installed feature. Factory 
installed options are designated by the eighth character in 
the catalog number. Unmodified S611 soft starters have an 

N

 as their eighth character. S611 soft starters with the pump 

control option have a 

P

 as their eighth character, as in 

S611xxx

P

3S.

Installation

Install and wire your S611 soft starter per the instructions 
found in the beginning of this manual. 

Setup 

All pump control parameters are set via the UI. Units 
configured with the pump control option can activate this 
feature by selecting the pump option under the UI “Start 
Method” parameter. 

Adjustment

All of the adjustments to the S611 soft starter are made as 
noted in this user manual. The major difference between the 
standard S611 soft starter and one with the pump start 
option is the special algorithm for gentle start and stop with 
centrifugal flow loads to minimize the potential for water 
hammer. 

Using the UI, set the S611 soft start configuration 
parameters described below:

The 

Start Ramp Time

 parameter adjusts the start ramp. It has 

a standard range of 0.5–180.0 seconds. The factory default is 
20.0 seconds. The soft stop time is adjusted by 

Pump Stop

which has a range of 5.0–120.0 seconds with the factory 
default being 10.0 seconds. (

Note:

 The 

Stop Ramp Time

 

setting used in non-pump S611s has no effect on units with 
the Pump Control Option installed if start method is Pump 
Start.) These adjustments are application dependent, and 
should be made to minimize any surge or water hammer 
effects. Typically Pump Stop would not be set short because 
the stop might not differ much from a coast-to-stop. The soft 
stop time adjustment may often be in the range of 30–40 
seconds, but needs to be set appropriately for the system 
requirements. If reduction or elimination of water hammer is 
not achieved, it may be necessary to lengthen 

Pump Stop

 to 

achieve the desired result. Note that long stop times will 
result in greater motor heating than shorter stop times. This 
can affect the number of start/stop cycles allowed per hour 
due to the S611 soft starter or motor thermal limits.

Pump Control Option

100%

tr

Start

Soft Pump Stop

Speed

Time (Seconds)

ts

Run

Coast to Stop

www.comoso.com

Содержание S611

































































































Отзывы: