14
Sit-to-Stand Techbench
Installation Manual
SIT-TO-STAND TECHBENCH INSTALLATION MANUAL
Eaton.com/techbench
A. Adjusting the levelers
•
Level the bench� Using bubble level, adjust the four
levelers as required to achieve both front to back
and side to side level� Adjust using ¾” box
wrench on check nut�
Leveler
¾" across flat
check nut
SECTION IV - Setting up and using the bench
Page 15 of 44
Description
The DP1CS is equipped with display and memory and is compatible with DESKLINE control boxes. The DP1CS
is available as a 1-channel version for operation of the parallel channels up and down. The actual height of
the desk is shown in the display. The display is of the LED type with a yellow light and 10 mm high digits.
Up and down (
^
V):
You just either have to activate the up or down button for parallel drive and the system will drive until
releasing the button again or when the system reaches end position.
Memory:
The four small buttons are used for memory drive/storing memory.
Store memory
• Press S – button, the display will flash “S” for 2 seconds
• Within these two seconds press one of the small buttons with numbers “1”, “2” or “3” and the position
will be stored at this button.
• The panel will acknowledge by showing “1”, “2” or “3” in the display depending on the chosen position
Memory drive
Press one of the memory buttons and the system will start driving to the pre-programmed memory position.
Keep the button pressed until the position is reached.
Display function
Shows the actual height in either cm or inch and can display error codes.
Operation of the DP1CS
Parallel up
Parallel down
Memory 1
Memory 2
Memory 3
Store memory
S
1
2
3
B. Operating the height adjustable worksurface
Your command bench is equipped with a DP1CS control pad�
Normal operation:
To run the desk up or down press the UP or DOWN arrow button
(
V
or V), and keep it pressed until the desk reaches the desired
height� The display will count up or down while running, and after
stopping it will continually show the current height of the desk�
As a safety precaution, your Sit-to-stand techbench is pre-
programmed to “single reference” mode� In “single reference”
mode, the controller requires the presence of four healthy lift
motors� In the event of a lift motor fault condition, the controller
will disable the signal to the remaining motors, preventing the
movement of the worksurface�
NOTICE
The bench’s lift motors have sensors that will detect
an obstruction when moving� If the work-surface is
jarred during operation or an obstruction is sensed, the
worksurface will stop movement and automatically begin to
move in the opposite direction�
Store a memory position:
The 4 small buttons are used for storing memory�
•
Press the “S” button; the display will flash “S” for 2 seconds
•
Within these two seconds press one of the small buttons
with numbers “1”, “2” or “3” and the position will be stored
at this button�
•
The panel will acknowledge the setting by showing “1”, “2”
or “3” in the display, depending on the chosen position
Memory Drive
Press and hold one of the memory buttons and the system
will start driving to the pre-programmed memory position�
Keep the button pushed until the position is reached�
Display Function
Shows the actual height either in inches or cm� The display
also shows error codes�
Adjust the display to show the correct height:
It may be necessary to adjust the height display after the
initial set up of the bench� Simultaneously press the “UP” and
“DOWN” arrow buttons (/\ or \/) and keep them pressed for
5 seconds� This allows the initial height to be re-set� Until the
initial height is re-set, the display will show three minuses (- -
-)� Thereafter the display will revert to showing the height� The
height can then be adjusted by pressing either /\ or \/ until the
correct height has been set� The system will return to normal
operation (and give a short blink) after 5 seconds of inactivity
on the buttons� The feature can be disabled via configuration
after which pressing the /\ and \/ buttons at the same time will
be considered an illegal keypress�
Switch between cm and inches:
Your DP1CS control pad is pre-configured to display in
inches� Switching between cm and inch can only be done
via the DPF configurator�
Adjusting the light intensity of the LED display
Possible light settings are off, 6%, 12%, 19%, 25%, 37%,
50%, 75% and 100%�
The adjustment can only be done via the DPF configurator�
Adjusting the light timeout
Possible light timeouts are: 0-15 sec and off�
The adjustment can only be done via the DPF configurator�
