Eaton IQ 250, Руководство пользователя и инструкция по установке

Страница: 123 / 142

A
IQ 250/260 Meter Appendix B:
Modbus Mapping
7536 - 7536 30007 - 30007 Operating Mode Screen Enables UINT16 bit-mapped -------- eeeeeeee eeeeeeee = op mode screen rows on/off, rows top to
bottom are bits low order to high order. 1
753E - 753E 30015 - 30015 User Settings Flags UINT16 bit-mapped ---g--nn srpdywf- g = enable alternate full scale bar graph current (1=on,
0=off)
nn = number of phases for voltage & current screens
(3=ABC, 2=AB, 1=A, 0=ABC)
s = scroll (1=on, 0=off)
r = password for reset in use (1=on, 0=off)
p = password for configuration in use (1=on, 0=off)
d = daylight saving time changes (0=off, 1=on)
y = diagnostic events in system log (1=yes, 0=no)
w = power direction (0=view as load, 1=view as generator)
f = flip power factor sign (1=yes, 0=no) 1
753F - 753F 30016 - 30016 Full Scale Current (for load % bar graph) UINT16 0 to 9999 none If non-zero and user settings bit g is set, this value replaces
CT numerator in the full scale current calculation. 1
7540 - 7547 30017 - 30024 Meter Designation ASCII 16 char none 8
7548 - 7548 30025 - 30025 Reserved Set to 0. 1
7549 - 7549 30026 - 30026 COM2 setup UINT16 bit-mapped ----dddd -ppp-bbb 1
754A - 754A 30027 - 30027 COM2 address UINT16 1 to 247 none 1
754B - 754B 30028 - 30028 Limit #1 Identifier UINT16 0 to 65535 Use Modbus address as the identifier (see notes 7, 11, 12). 1
754C - 754C 30029 - 30029 Limit #1 Out High Setpoint SINT16 -200.0 to +200.0 0.1% of full scale Setpoint for the "above" limit (LM1), see notes 11-12. 1
754D - 754D 30030 - 30030 Limit #1 In High Threshold SINT16 -200.0 to +200.0 0.1% of full scale Threshold at which "above" limit clears; normally less than
or equal to the "above" setpoint; see notes 11-12. 1
754E - 754E 30031 - 30031 Limit #1 Out Low Setpoint SINT16 -200.0 to +200.0 0.1% of full scale Setpoint for the "below" limit (LM2), see notes 11-12. 1
754F - 754F 30032 - 30032 Limit #1 In Low Threshold SINT16 -200.0 to +200.0 0.1% of full scale Threshold at which "below" limit clears; normally greater
than or equal to the "below" setpoint; see notes 11-12. 1
7550 - 7554 30033 - 30037 Limit #2 SINT16 5
7555 - 7559 30038 - 30042 Limit #3 SINT16 5
755A - 755E 30043 - 30047 Limit #4 SINT16 5
755F - 7563 30048 - 30052 Limit #5 SINT16 5
7564 - 7568 30053 - 30057 Limit #6 SINT16 5
7569 - 756D 30058 - 30062 Limit #7 SINT16 5
756E - 7572 30063 - 30067 Limit #8 SINT16 5
7573 - 7582 30068 - 30083 Reserved Set to 0. 16
7583 - 75C2 30084 - 30147 Reserved Set to 0. 64
75C3 - 75E5 30148 - 30182 Reserved Set to 0. 35
75E6 - 75E6 30183 - 30183 Programmable Settings Update Counter UINT16 0-65535 Increments each time programmable settings are changed;
occurs when new checksum is calculated. 1
75E7 - 7626 30184 - 30247 Reserved for Software Use Set to 0. 64
Block Size: 248
dddd = reply delay (* 50 msec)
ppp = protocol (1-Modbus RTU, 2-Modbus ASCII, 3-DNP)
bbb = baud rate (1-9600, 2-19200, 4-38400, 6-57600)
Same as Limit #1. Same as Limit #1. Same as Limit #1.
www.eaton.com IB02601006E MM-17