E.F. Johnson Company 53SL ES Series Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 190

background image

6-28

53SL ES Series Mobile Radio Operating Manual April 2009

Text Messaging

Section 6 - Conventional Mode Features

Note

The channel spacing is not set with P25 channels because it is always narrow, and the
squelch cannot be changed because the setting is critical for proper receiver operation.

SQ ADJUST

(Analog Only) - Changes the preset squelch setting on that channel. The

default setting is “0” and values of –7 to +7 can be selected. Increasing this setting
7 causes the squelch to open sooner so that weaker signals can be received, and
decreasing it toward –7 causes the opposite to occur.

TG ID

(P25 Only) - Selects the talkgroup for the selected channel. Rotate the Select

switch to display the alias of each preprogrammed talkgroup and then press it to store
the desired talkgroup. A single beep sounds when the switch is pressed (if that option is
selected).

Transmit Type

(P25 Mixed Mode Only) - If the selected channel is a mixed mode,

analog and P25 channel, this selects the transmit type. Either Analog or Digital (P25)
can be selected. This then determines if a Tx Code or Tx NAC is programmed above.

6.15

Text Messaging

If enabled, mobile radios have text message receiving capability (digital conventional
mode only).

Note

Mobile radios can receive text messages, but cannot transmit them. All received messages
are limited to 200 characters.

6.15.1 Data Setup for Text Messaging

A mobile subscriber can receive a text message from another subscriber on a digital
conventional channel regardless of whether the channel uses a repeater.

The radio’s text message menu contains the item “Set R to R”. The default for this setting
is enabled, in which the following capabilities are operable:

• A text message can be received from radios on a simplex digital channel

• A text message can be received from radios on a digital channel with a repeater (if

repeater talk-around is enabled)

• The repeater in use is programmed for Repeated Data mode (not supported by EFJ 2600

repeaters)

«
...
106
107
108
109
110
...
»

Содержание 53SL ES Series































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 53SL ES Series

Бренд: Uniden Страницы: 2

Бренд: 4RF Страницы: 2

Бренд: B&B Electronics Страницы: 55

Zlinx ZP Series

Бренд: B&B Electronics Страницы: 70

Бренд: Hama Страницы: 19

Бренд: Hama Страницы: 64

Бренд: Audiovox Страницы: 28

Бренд: Blaupunkt Страницы: 34

EDDINGTON EDD-DAB-BLK

Бренд: MAJORITY Страницы: 26

Бренд: Emerson Страницы: 16

Бренд: Emerson Страницы: 16

Бренд: Emerson Страницы: 16

Бренд: Vertex Standard Страницы: 5

Бренд: KIDdesigns Страницы: 23

Бренд: Vertex Standard Страницы: 72

Бренд: DeWalt Страницы: 48

Бренд: DeWalt Страницы: 16

Бренд: DeWalt Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды