E.F. Johnson Company 53SL ES Series Скачать руководство пользователя страница 123 | Manualshive

Страница: 123 / 190

background image

53SL ES Series Mobile Radio Operating Manual April 2009

7-11

Sending Status Conditions

Section 7 - SMARTNET / SmartZone / P25 Trunked Features

Note

Only the message number assigned to the alias is sent– not the actual text of the alias. For
example, If MSG 1 is assigned to alias “In Service”, “MSG 1” is sent– not “In Service”.

7.8

Sending Status Conditions

The status feature allows you to send your current status to your dispatcher. Up to eight
status conditions can be preprogrammed, and they are identified by an alias. If the Status
option switch is programmed, status conditions are sent as follows:

1

Momentarily press the Status option switch. The alias of the current status condition is
displayed.

2

To change the current status, rotate the Select switch until the desired status is
displayed. Then press the Select switch to accept that status. A single beep sounds
when the Select switch is pressed (if that option is selected). One of the following
conditions then occurs:

- If five beeps sound and “ACK RCVD” is displayed, the status was received and

acknowledged by the system.

- If after five tries the message is not acknowledged, a tone sounds and “NO ACK” is

displayed.

Note

Only the status number assigned to the alias is sent– not the actual text of the status
condition alias itself

7.9

Emergency Alarm and Call

Emergency Alarms and Calls are separate functions that can be individually enabled or
disabled on each SMARTNET/SmartZone and P25 Trunked system. The Emergency
option switch (or menu selection) is required for these functions. Other emergency
features are as follows:

• Emergency Alarms are transmitted on the selected talkgroup if emergency calls are

disabled, and on the emergency talkgroup if emergency calls are enabled.

• Emergency Call talkgroup selection priority is as follows. For example, if a global

emergency channel is not programmed, the emergency talkgroup of the selected
channel is used and so on.

- Global (radio wide) emergency channel

- Emergency group of the selected channel

«
...
121
122
123
124
125
...
»

Содержание 53SL ES Series































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 53SL ES Series

Бренд: B&G Страницы: 129

Бренд: Vertex Standard Страницы: 2

Бренд: Yaesu Страницы: 6

Бренд: Uniden Страницы: 24

Бренд: Parametric Страницы: 9

Бренд: Denver Страницы: 12

Бренд: Uniden Страницы: 24

Бренд: Swissvoice Страницы: 104

Бренд: Caliber Страницы: 18

Бренд: Enrock Marine Страницы: 2

RoadCom-Multi Norm

Бренд: Team Electronic Страницы: 11

Бренд: QFX Страницы: 6

Бренд: KIDdesigns Страницы: 23

Бренд: Vertex Standard Страницы: 72

Бренд: IDENTEC SOLUTIONS Страницы: 11

Бренд: BTECH Страницы: 83

Бренд: Excera Страницы: 34

Бренд: Kensington Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды