E.F. Johnson Company 53SL ES Series Скачать руководство пользователя страница 180

Страница: 180 / 190

10-6

53SL ES Series Mobile Radio Operating Manual April 2009

Error Messages

Section 10 - Tones & Error Messages

No Items

- The menu the user tried to access does not have any items.

No List -

No list is available for the selected channel.

No Message -

No message is programmed for transmission.

No Reply -

Radio cloning failed due to no response.

No Sat Rec

- The user has a tried to enter GPS mode but the receiver does not have a

satellite lock.

No Service -

OTAR service is not available.

No Site -

No site with a verified ID is yet on the dynamic site list.

No Keys -

No keys are available for the key select function.

Out Of Rng -

This error indicates no control channel has been found for trunking

operation.

Parms Fail -

The checksum of the profile / user parameters does not match the calculated

checksum. This indicates that there is an error in the parameters file. This message only
occurs if the redundant copy of the parameters is also corrupt or is unable to be used.

Rekey Fail -

This error indicates a failure in a rekeying process.

Rx Only -

The selected channel is Rx only.

Sts Failed -

No acknowledgement was received while sending a status report.

Timeout -

A time out has occurred in attempting the current function.

Too Hot -

The mobile has passed the TOO HOT temperature threshold. Under these

conditions the radio will not allow Tx.

Tx Timeout -

The Tx time-out timer has expired and Tx has been terminated.

VOLTAGE HI -

The input voltage to the mobile is too high.

VOLTAGE LO -

The input voltage to the mobile is too low.

Write Fail -

The radio is unable to write to the EEPROM.

Zone Fail -

The radio has been programmed with more zones than its options allow.

Reg Failed

- This error indicates that the radio was unable to complete data registration on

the system.

Содержание 53SL ES Series































































































































































































Результаты поиска

Содержание 53SL ES Series

Отзывы:

Похожие инструкции для 53SL ES Series

Бренды по названию

Популярные бренды

E.F. Johnson Company 53SL ES Series, Руководство по эксплуатации

Результаты поиска

Содержание 53SL ES Series

Отзывы:

Похожие инструкции для 53SL ES Series

Бренды по названию

Популярные бренды