E.F. Johnson Company 53SL ES Series Скачать руководство пользователя страница 179

Страница: 179 / 190

53SL ES Series Mobile Radio Operating Manual April 2009

10-5

Error Messages

Section 10 - Tones & Error Messages

Fixed Low -

The selected channel or group is strapped to low power and thus high power

can not be selected.

HC08 Fail-

The HC08 was not initialized correctly and cannot be accessed for flash reads

and writes, tone generations, etc. Applicable to ES series radios only.

Hot

- The radio has passed the "Hot" temperature threshold and will only transmit in low

power.

Invalid -

The received input from the user does not fit the criteria necessary for the

feature.

Invalid ID -

The received ID from the user was not a valid ID.

Invald Key -

The key pressed by the user was not valid for the current situation.

Invalid TG

- This error indicates that the talkgroup entered into the radio by the user is

invalid.

Invld User

- This error indicates that the user’s radio ID was rejected by the system. This

message is primarily related to data registrations.

Invld Ch -

The channel entered by the user in keypad programming is not valid.

Key Fail -

The encryption key required by the current selected group/channel is not valid.

Kypd Lockd -

The keypad lock function is active and key presses are not accepted in this

mode.

Kset Fail -

The encryption key set chosen by the user is not valid.

List Only -

Direct entry of a unit ID or phone number is disabled.

Locked -

A selector lock command has been received and zone and channel changes are

not accepted.

Lost Signl -

Signal from the infrastructure has been lost during an interconnect call.

Low Power

- This error indicates that the current channel is strapped to low power and

that the user can not select high power at this time.

Msg Failed -

No acknowledgement was received while sending a status report.

Narrow -

The current conventional channel is programmed as a narrow channel.

No Ack -

The radio did not receive an ACK for the current signaling attempt.

No Edit -

The current list is not able to be edited.

No Encrypt -

Encryption is not available for the selected channel.

Содержание 53SL ES Series































































































































































































Результаты поиска

Содержание 53SL ES Series

Отзывы:

Похожие инструкции для 53SL ES Series

Бренды по названию

Популярные бренды

E.F. Johnson Company 53SL ES Series, Руководство по эксплуатации

Результаты поиска

Содержание 53SL ES Series

Отзывы:

Похожие инструкции для 53SL ES Series

Бренды по названию

Популярные бренды