E.F. Johnson Company 53SL ES Series Скачать руководство пользователя страница 178 | Manualshive

Страница: 178 / 190

background image

10-4

53SL ES Series Mobile Radio Operating Manual April 2009

Error Messages

Section 10 - Tones & Error Messages

Bad Fl Fmt -

A profile/or user parameters have been downloaded to the radio that do not

match the file format supported by the firmware/software in the radio.This message may
appear on initial power up following a firmware upgrade. In such cases the message can be
cleared by doing a read/write of parameters using PCC version 2.6.x or later.

Bad Hrdwar -

The software was loaded on the wrong platform. The boot loader version

does not match the expected boot loader version. I.e., the frequency band from the ESN
may not match the RF deck frequency band.

Batt Low -

The battery voltage has been detected as being low.

Busy -

A call has been attempted and the system has responded that no channels are

available for assignment.

Busy Tmout -

The radio previously received a busy response from the system and it has

not received a channel grant before the busy time-out timer has expired.

Disabled -

The selected channel is disabled.

Clear Only -

The selected channel or group is strapped clear only and that a secure call

can not be made.

Corupt Prm -

The parameters checksum is correct, but an error exists in the parameters

file.

Cycle Power

- This error replaces the previous RX Back End Fail error. It occurs when

the radio has a communication failure with the RF Deck. This error only occurs with the X
and ES radio platforms.

Denied -

A group call attempt has received a DENIED response from the system.

Deny -

A unit or interconnect call attempt has received a DENIED response from the

system.

Disabled -

The feature that the user is attempting to use has been disabled on the radio

either by programming or by factory options.

DSP Failed -

The main processor and the DSP have failed to complete their startup

procedure at powerup.

EEPRM Fail -

The main processor has timed out while trying to validate or invalidate the

profile/user parameters in the EEPROM.

Encryp Bad -

The main processor and the Encryption Module have failed to complete

their startup procedure at power up.

Fixed High -

The selected channel or group is strapped to high power and thus low power

can not be selected.

«
...
176
177
178
179
180
...
»

Содержание 53SL ES Series































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 53SL ES Series

Heritage Bluetooth

Бренд: HAEGER Страницы: 40

Zlinx ZP24D-250RM-SR

Бренд: B&B Electronics Страницы: 2

Бренд: Lanzar Страницы: 12

Бренд: Akai Страницы: 12

Бренд: Tekcom Industries Страницы: 14

Бренд: Uniden Страницы: 2

Бренд: Mimomax Страницы: 56

Бренд: nedis Страницы: 100

Бренд: Sunwave Страницы: 46

Бренд: Com-Net Ericsson Страницы: 20

Бренд: PURE Страницы: 120

Бренд: SimonsVoss Страницы: 16

Бренд: stabo Страницы: 32

Бренд: EBENCH Страницы: 8

Бренд: Sony Страницы: 2

ICF-CDK70 - Currently Not Available

Бренд: Sony Страницы: 2

ICF-CDK70 - Currently Not Available

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды