E.F. Johnson Company 53SL ES Series Скачать руководство пользователя страница 34

Страница: 34 / 190

2-4

53SL ES Series Mobile Radio Operating Manual April 2009

Standard Control Head

Section 2 - Controls & Display

Table 2.1

Standard Control Head Display Symbols

Standard Control Head Display Symbols

Operating Mode Symbols

Unit (or Private) call mode active

Busy (displayed when radio enters a busy transmit state)

Monitor mode enabled

Interconnect mode enabled

Security enabled

• Keypad programming/edit mode - displayed when the radio is in a mode where

the user can edit radio parameters.

• P25 data context enabled - radio is ready for data operations or call history

(only when radio is in conventional unit call, call alert or text messaging and an

applicable unit ID is selected.)

• P25 data channel grant (radio is operating on a data channel) or text message

mode active.

Status Display Symbols

Scan enabled

The current channel is the priority channel in the enabled scan list (only when scan is on or

when in scan edit mode; located in left position)

The current channel is the priority 2 channel in the enabled scan list (only when scan is on

or when in scan edit mode; located in left position)

The current channel is in the enabled scan list (only when scan is on or when in scan edit

mode; located in left position)

Radio wide scan mode enabled

Selected channel is in radio wide scan list (only when radio wide scan is on or when in radio

wide scan edit mode)

Repeater talk-around enabled

Содержание 53SL ES Series































































































































































































Результаты поиска

Содержание 53SL ES Series

Отзывы:

Похожие инструкции для 53SL ES Series

Бренды по названию

Популярные бренды

E.F. Johnson Company 53SL ES Series, Руководство по эксплуатации

Результаты поиска

Содержание 53SL ES Series

Отзывы:

Похожие инструкции для 53SL ES Series

Бренды по названию

Популярные бренды