E.F. Johnson Company 53SL ES Series Скачать руководство пользователя страница 176

Страница: 176 / 190

10-2

53SL ES Series Mobile Radio Operating Manual April 2009

Supervisory Tones

Section 10 - Tones & Error Messages

• Dynamic regrouping has been exited but the dynamic regrouping channel is still

selected (Section 7.12).

Single Short Medium-Pitch Tone

• A valid key has been pressed.

Single Short Low-Pitch Tone

• An invalid key has been pressed.

Medium Tone (No Acknowledge)

• The paged mobile did not acknowledge the page (Section 7.6).

• The message that was sent has not been acknowledged (Section 7.7).

• The status condition that was sent has not been acknowledged (Section 7.8).

Five Beeps (Recurring)

• The page was received (Section 7.6).

Two Short Tones

• A unit-to-unit call was received (Section 7.6).

Five Beeps

• The paged mobile received the page and acknowledged it (Section 7.6).

• The message that was sent has been received and acknowledged (Section 7.7).

• The status condition that was sent has been received and acknowledged (Section 7.8).

Four Beeps

• The emergency alarm condition was acknowledged (Section 7.9).

• Four low beeps indicate the call back mode (the system is no longer busy).

Содержание 53SL ES Series































































































































































































Результаты поиска

Содержание 53SL ES Series

Отзывы:

Похожие инструкции для 53SL ES Series

Бренды по названию

Популярные бренды

E.F. Johnson Company 53SL ES Series, Руководство по эксплуатации

Результаты поиска

Содержание 53SL ES Series

Отзывы:

Похожие инструкции для 53SL ES Series

Бренды по названию

Популярные бренды