Dynisco UPR700 Скачать руководство пользователя страница 60

Страница: 60 / 72

Range:

nodbS, JbuS. Modbus/Jbus selection.

Default value:

Modbus.

COMMUNICATION TYPE - Group 3

Available:

Only if SC.ADR is different than Off.

Upper display: Number of bits.
Lower display: SC.FRM
Range:

8, 8 E, 8 O. 8 bit without parity, 8 bit + even parity, 8 bit + odd parity.

Default value:

8 bit without parity.

COMMUNICATION BAUD RATE - Group 3

Available:

Only if SC.ADR is different than Off.

Upper display: Baud rate.
Lower display: SC.BDR
Range:

600, 1200, 2400, 4800, 9600, 19200.

Default value:

19200.

LOADING DEFAULT DATA - Group 3

Available:

Only if access to level 3 is allowed.

Upper display: OFF
Lower display: DEFLT
Range:

Use

▼

▲

keys to switch the upper display from OFF to On 3, then press FUNC key

to load the default data of the parameters belonging to group 1, group 2, group 3.

12.4

ROUP

4 D

EFAULT

ARAMETERS

SHUNT CALIBRATION - Group 4

Available:

Always

Upper display: OFF if shunt calibration is disabled, On if shunt calibration is enabled.
Lower display: SHUNT
Range:

OFF, On.

Default value:

On.

SHUNT VALUE - Group 4

Available:

Only if SHUNT parameter is on.

Upper display: Shunt value.
Lower display: SHNT.%
Range:

From 40.0 to 100.0%

Default value:

80.0%

Содержание UPR700









































































Результаты поиска

Содержание UPR700

Отзывы:

Похожие инструкции для UPR700

Бренды по названию

Популярные бренды

Dynisco UPR700, Инструкция по установке и эксплуатации

Результаты поиска

Содержание UPR700

Отзывы:

Похожие инструкции для UPR700

Бренды по названию

Популярные бренды