background image

28

In Industrial applications, amplified units have a middle or end number of 4, 5, or 6. The S840-000-
1C has a 4-20 mA signal output; the PT150-7.5M has a 0-5 Vdc signal output, while PT276-5M has
a 0-10 Vdc signal output.

If you have an amplified transducer, or other amplified input, skip to Section 8.4.2.

The UPR700’s default setting is strain gage input. To verify that the input is set for strain gage, press
the 

FUNC

 key until 

nonE

 and 

GROUP

 show on the display. Press the 

 key until 

5

 shows in the

upper display. Press the 

FUNC

 key and the upper display should show 

Str

 while the lower display

shows 

PI.TYP

. If not, press the 

 or 

 key until the upper display changes to 

Str

 (for strain gage).

Press the 

FUNC

 key to set the value. The upper display changes to 

tc

 with 

SI.TYP

 on the lower

display. Press the 

RESET

 key to return to the active display.

Remember to change the jumper settings to correspond to the proper input as shown in Figure 6 for
board location and Figure 7 for amplified input jumpers.

Fig. 6

UPR700 Board Location

Содержание UPR700









































































Отзывы: