Dynisco UPR700 Скачать руководство пользователя страница 44

Страница: 44 / 72

upper display. Press the

FUNC

key and the upper display should show

OFF

while the lower display

shows

SHUNT

. If the upper display does not show

OFF

, press the

▼

▲

key until the upper display

changes to

OFF

. Press the

FUNC

key to set the value and press

RESET

to return to the operating

screen.

Press the

FUNC

key until

nonE

and

GROUP

show on the display. Press the

▲

key until

shows in

the upper display. Press the

FUNC

key and the lower display changes to

ZERO.C

. The upper display

shows

OFF

. With the input at the low scale value, press the

▼

▲

keys until the upper display

changes to

. Press the

FUNC

key to calibrate the zero value. When the lower display changes to

SPAN.C

, zero calibration is complete. Press the

▼

▲

keys until the upper display changes to

CLEAr

. Press the

FUNC

key to restore the linear factory calibration of the span value. When the

legend

DSP.FL

appears in the lower display, calibration is complete. Press

RESET

to return to the

operating screen.

9.2

NSTRUMENT

ALIBRATION

NOTE:

In this section the word

Calibration means to set the Instrument to an internationally

recognized standard, independent of input device.

9.2.1 S

ETTING

THE

NTERNAL

WITCH

FOR

NSTRUMENT

ALIBRATION

The instrument calibrations are accessible by an internal dip-switch (see below). This is done to
protect the calibration data area of the EEPROM.

NOTE:

The instrument is shipped with the fitted circuits fully calibrated.

Remember to change the switch settings back to the proper input as shown in Figure 14 for board
location and switch settings.

Remove the instrument from its case by gently pulling back the tabs on either side of the display.
This can be done with the unit powered, without fear of damage.

CPU BOARD

DIP SWITCH POSITIONS

Operating Mode

SW1 OFF

SW2 OFF

Calibration Mode

SW1 ON

SW2 OFF

Factory Mode

SW1 OFF

SW2 ON

Security Mode

SW1 ON

SW2 ON

Содержание UPR700









































































Результаты поиска

Содержание UPR700

Отзывы:

Похожие инструкции для UPR700

Бренды по названию

Популярные бренды

Dynisco UPR700, Инструкция по установке и эксплуатации

Результаты поиска

Содержание UPR700

Отзывы:

Похожие инструкции для UPR700

Бренды по названию

Популярные бренды