Dynatron 150plus Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 65

background image

Dynatron

®

150

plus

Battery Operation

16

Battery Requirements

• 12 volt and at least 5 amps peak current (1.5 ampere hours minimum).

Do not substitute the Dynatron battery without first confirming with Dynatronics
that the battery you are purchasing may be used with this device.

• Battery Adapter Cord

- Cigarette lighter plug on one end (to attach to the battery pack) and a barrel

plug on the other end (to fit a .325 barrel jack).

- The cord must be a high quality gauge wire. (Radio Shack carries a high

quality cord that is recommended. Cat. No. 270-1534D. This cord comes
with a 2 amp fuse which must be replaced with a 5 amp fast blow fuse.)

Note: If a low-quality gauge cord is used, you can get the BATT LO error
when the battery is not low.

Battery Life

The length of time that a unit can be used with a battery pack is dependent on several
factors:

•  The amperage of the battery pack. A larger amperage will provide longer use.

•  The modality used. Ultrasound requires more power than stim modalities.

•  The intensity of the treatments. The higher the intensity, the higher the

consumption of power.

• The amount of charge remaining on the battery.

As a general rule, the unit may be run continuously for 30 minutes to several hours
depending on these factors.

«
...
20
21
22
23
24
...
»

Содержание 150plus


































































Отзывы:

Нет отзывов

Похожие инструкции для 150plus

Бренд: GE Страницы: 24

Бренд: Keithley Страницы: 32

Бренд: Raymarine Страницы: 70

Бренд: Harbor Freight Tools Страницы: 4

Бренд: CAIRE Страницы: 2

Бренд: XAG Страницы: 24

Бренд: DB Industries Страницы: 60

Бренд: vc999 Страницы: 55

Бренд: Salsbury Industries Страницы: 4

Бренд: IBEX Страницы: 4

Бренд: Zodiac Страницы: 2

Бренд: Zipper Mowers Страницы: 37

Бренд: Zimmer Страницы: 46

Бренд: uniprox Страницы: 3

2261998USBA1-XX

Бренд: MMF POS Страницы: 5

Бренд: Kanlux Страницы: 4

Бренд: DAAB Страницы: 12

Бренд: Jäger Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды