Dynatron 150plus Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 65

background image

Dynatron

®

150

plus

Calibration Procedure

42

Te soundhead type is displayed for about
one second. Next, the display shows the
stored frequency values for the
soundhead that is being calibrated. The
output power display is set to a value of
zero. The LED for 1 MHz should be
illuminated indicating the soundhead is
now ready to be calibrated for this
frequency. If it is not, press the toggle
key to select 1 MHz now.

3. Press

STOP and the TIME UP ARROW

simultaneously to enter the Temperature
Mode. The temperature of the soundhead
is displayed in the time display window.
The soundhead must be at a temperature
between 72 and 75 degrees. If the
soundhead is not within this range, warm the water and/or the head before
continuing. Press STOP to get out of the temperature mode. At this point there is
zero output from the device. Zero the scale on your Ultrasound power meter now.
When the scale is at zero on your power meter, press the START key to begin.

4. Press

the

UP/DOWN ARROW keys located next to the Power display window on

the Dynatron 150plus until the power meter shows 1.0 W/cm

2

.

5. When the watts reading on the meter is at 1.0 W/cm

2

for the soundhead and the

reading is stable, press the DUTY CYCLE toggle key (this is the key that selects
10%, 20%, 50% or Continuous).

6. The Dynatron 150plus performs the calculation internally for the “Z” (impedance

value) and the coupling value. These values are automatically entered and stored in
the Head Parameters for the device (this operation is automatic and invisible to the
user). Record these values on the calibration sheet for future reference.

7. Press the frequency toggle key to select 2 MHz. The 2 MHz LED will light

indicating the soundhead is now ready to be calibrated at the frequency. Repeat
steps 3 through 6 above.

8. Press the frequency toggle key to select 3 MHz. The 3 MHz LED will light

indicating the soundhead is now ready to be calibrated at the frequency. Repeat
steps 3 through 6 above.

9. If you wish to cancel the calibration procedure without storing any new

calculations, press the PAUSE key.

10. This completes the calibration of one soundhead. For devices that use more than one

soundhead, you must calibrate each of those soundheads individually.

Soundhead Types Table

Smart Heads:

Time Display = HS
Power

Display:

2 cm2 = 2

5 cm2 = 5

10

cm2

=

10

Older Sound Heads:

Time Display only:

1 cm2 = H 1

2 cm2 = H 2

5 cm2 = H 5

10 cm2 = H10

«
...
46
47
48
49
50
...
»

Содержание 150plus


































































Отзывы:

Нет отзывов

Похожие инструкции для 150plus

Бренд: RayLight Страницы: 34

GAZELLE FREESTYLE

Бренд: Gazelle Страницы: 10

Бренд: Latham Страницы: 19

Бренд: MacDon Страницы: 46

Бренд: MacDon Страницы: 82

Бренд: Mac Medical Страницы: 2

Бренд: MACDEV Страницы: 8

Mentor Touch ET750

Бренд: MAC TOOLS Страницы: 24

Бренд: MA lighting Страницы: 10

Бренд: Mackie Страницы: 34

Бренд: Mackworth Страницы: 38

Бренд: P&P Страницы: 6

Бренд: Ultrawave Страницы: 30

Бренд: Ultrasound Technologies Страницы: 12

Бренд: YASKAWA Страницы: 40

RAISED GARDEN BED

Бренд: Yardfully Страницы: 2

i-Digits Access

Бренд: Össur Страницы: 231

MIAMI J ADVANCED

Бренд: Össur Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды