Dynatron 150plus Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 65

background image

Dynatron

®

150

plus

Problem Solving

46

your whirlpool temperature is hot enough to cause the treatment to stop, you may
need to adjust the temperature of the whirlpool.

Soundhead Temperature Too Cold

If the soundhead has been sitting in a cold room or vehicle, it could be too cold to
operate when you turn the device on. The keypad may not respond to key presses
and you will be unable to use the device until the soundhead is sufficiently warmed.
You must raise the temperature of the soundhead to about 60 degrees F. in order for
the machine to recognize that the soundhead is present and to proceed with setting up
a treatment. You can accomplish this with any of the following methods:

1. Press the flat face of the soundhead against the palm of your hand for 30 to 60

seconds to warm it slightly. This usually provides adequate warmth to the crystal
to raise the temperature to the minimum acceptable level. Once the crystal
reaches this level, you can proceed with treatment.

2. You can also place the soundhead in room temperature water to warm the crystal.

However, do not place the soundhead in very hot water when the crystal is this
cold as it could damage the crystal.

Error Message in the Display

Certain conditions can cause an error in operation. When this occurs, the machine
will not allow a treatment to be set up or delivered and will display an error message
in the LED displays. An error message can consist of any combination of alpha-
numeric characters which are not normally expected at any given point in treatment
setup or delivery. Some errors are easily resolved by the following methods.

• Press STOP to stop the treatment (if any), and turn the machine off then on again.

• Check to be sure the soundhead has not become disconnected from the machine.

The soundhead should be firmly plugged into its port. Only Dynatronics
soundheads may be used with this device. If the soundhead has been dropped, it
may be damaged. If the device operates normally with one soundhead, but not
with another, the problem may be a damaged soundhead and you must contact
Dynatronics Customer Service.

• Make sure the soundhead is not too hot. In this case the power LED display will

flash. Any other display indicates a problem not related to a soundhead that is too
hot. For hot soundheads, follow the instructions provided earlier in this section.

• Check to see if conditions may have caused moisture condensation in the device.

This could occur when the machine has become very cold (for example, if left
outdoors in a vehicle during winter), then is brought indoors to a warm, humid
environment (such as a whirlpool room). Condensation is a not a serious

«
...
50
51
52
53
54
...
»

Содержание 150plus


































































Отзывы:

Нет отзывов

Похожие инструкции для 150plus

Бренд: GALLERY Страницы: 18

Бренд: 1010music Страницы: 2

Бренд: 1010music Страницы: 4

Бренд: Mandam Страницы: 9

Бренд: Xebex Fitness Страницы: 15

Бренд: qeedo Страницы: 2

Бренд: SAMCHULLY Страницы: 48

Бренд: HAGER WERKEN Страницы: 2

Бренд: Waters Страницы: 4

Бренд: Waterpik Страницы: 2

Бренд: Balanced Body Страницы: 4

Бренд: Balanced Body Страницы: 2

Reformer Trapeze Combination

Бренд: Balanced Body Страницы: 164

Бренд: Balanced Body Страницы: 37

Littmann Classic II Pediatric

Бренд: 3M Страницы: 53

Бренд: Rowlinson Garden Products Страницы: 5

GPSMAP 9 3 Series

Бренд: Garmin Страницы: 222

Carestation 620

Бренд: GE Страницы: 268

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды