Dynatron 150plus Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 65

background image

Dynatron

®

150

plus

Technical Specifications

31

5. Immediately report any device malfunction to Dynatronics Customer Service

Department.

NOTE: BEFORE sending a device to Dynatronics for service, you must FIRST
obtain a return authorization number. Call Dynatronics’ Customer Service
Department at (801) 568-7000 (or Email to [email protected]), and discuss any
problems or required service to save time and ensure the machine is returned to you
as quickly as possible.

Routine Calibration Inspections

Government agencies regulate the frequency at which Ultrasound units must have
their calibration checked. Even though the Dynatron 150plus does an internal
diagnostic procedure at startup, the device must still be examined at the periodic
intervals specified by the governing agency.

To have the inspection performed by Dynatronics contact Dynatronics Customer
Service Department, the device will need to be shipped to Dynatronics for the
inspection. As an alternative, these periodic checks may be performed in your own
office by a local independent contractor who is expert in checking the calibration of
Ultrasound equipment.

The calibration procedure MUST be performed by a qualified Ultrasound
technician using the proper equipment.

Detailed calibration procedures may be obtained from Dynatronics Customer Service
at the number provided below.

Dynatronics will make available on request circuit block diagrams, component part
lists, descriptions, calibration instructions or other information which will assist the
user’s appropriately qualified technical personnel to repair those parts of the
equipment which are designated by Dynatronics as repairable and which will not
violate protection of Dynatronics’ proprietary information.

Authorized Service Center

All service of the Dynatron 150plus, except calibration, must be performed by
Dynatronics’ Service Department. For service, contact the following:

Dynatronics Customer Service Department
7030 Park Centre Drive
Salt Lake City, UT 84121
(800) 874-6251 or (801) 568-7000
Fax: (801) 568-7711

«
...
35
36
37
38
39
...
»

Содержание 150plus


































































Отзывы:

Нет отзывов

Похожие инструкции для 150plus

Бренд: Ecco Страницы: 3

Бренд: Mandam Страницы: 9

Бренд: G-Systems Страницы: 60

Бренд: G-Lab Страницы: 16

Бренд: G&G Страницы: 2

Бренд: Ultimate Healthcare Страницы: 2

Бренд: Ultimate Healthcare Страницы: 40

Бренд: Xaoc Devices Страницы: 8

Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology...

Бренд: M-Audio Страницы: 25

Exitronix LEMD Series

Бренд: BARRON Страницы: 6

Бренд: Cablexpert Страницы: 12

Бренд: Carbatec Страницы: 29

Бренд: PurAthletics Страницы: 2

Бренд: ultraMEDIC Страницы: 28

Бренд: Evermed Страницы: 16

Бренд: Enerpac Страницы: 36

NOVACAT X8 COLL

Бренд: Pottinger Страницы: 91

Бренд: Life Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды