Dynatron 150plus Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 65

background image

Dynatron

®

150

plus

Battery Operation

15

Battery Operation

Use ONLY a Dynatronics-Approved Battery

Contact Dynatronics or your Dynatronics dealer to purchase the optional battery or to obtain
specifications for an acceptable battery that may be used. Do not substitute another battery without first
confirming with Dynatronics that the battery you are purchasing may be used with this device.

Only use a battery that CANNOT be recharged while it is in use. Disconnect the battery charger
from the AC power source before using the battery to supply power to this device.

An optional battery is available for the Dynatron 150plus, allowing you to deliver
battery-powered treatments wherever power may be unavailable or unreliable. To
use the optional battery, do the following:

1. Before use, ensure the battery has been adequately charged. DISCONNECT the

battery charging cable from the battery while it is in use for treatment.

2. Plug the battery adapter into the jack labeled BATT on the back of the Dynatron

150plus device. Turn the battery pack ON.

3. Set up and deliver treatments as you normally do.

4. When available battery power is reduced to a certain level, the device will flash a

message BATT LO to indicate low battery power. The treatment can continue
but you will probably be unable to set up and deliver another treatment when the
current treatment has ended.

5. When the available battery power becomes too low to continue operating the

device, the BATT LO message is again displayed, the treatment intensity is
ramped down, and the machine is then shut OFF. Before you can continue with
battery operation of the device, you must recharge the battery. If battery power is
fully depleted, the message BATT BAD is displayed to indicate either a bad
battery or to indicate the battery must be recharged. Any treatments that were
running at that time will stop.

NOTE: Use the ON/OFF switch on the battery pack to control power to the device
during battery operation. While the battery is attached, the battery’s ON/OFF switch
controls power to the device.

«
...
19
20
21
22
23
...
»

Содержание 150plus


































































Отзывы:

Нет отзывов

Похожие инструкции для 150plus

Бренд: OMCA Страницы: 72

Бренд: Barko Hydraulics Страницы: 92

Бренд: Varec Страницы: 74

Бренд: Halyard Страницы: 84

Бренд: PAIDI Страницы: 48

BioHarmonex BH4

Бренд: Calivita Страницы: 38

Бренд: CAIRE Страницы: 91

Бренд: Jaga Страницы: 32

Бренд: KaVo Страницы: 4

ORTHOPANTOMOGRAPH OP 3D

Бренд: KaVo Страницы: 40

KEY Laser III 1243

Бренд: KaVo Страницы: 103

EXTRAmatic 9040

Бренд: KaVo Страницы: 56

ESTETICA E70 Vision

Бренд: KaVo Страницы: 48

Бренд: Kaya Safety Страницы: 5

Бренд: XTA Страницы: 20

Бренд: Kawai Страницы: 166

Бренд: Land Pride Страницы: 32

Бренд: Quark-Elec Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды