Dynatron 150plus Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 65

background image

Dynatron

®

150

plus

Ultrasound With Electrical Stim Input

17

Ultrasound With Electrical Stim Input

NOTE: The stimulator device to be connected to this unit shall comply with IEC 601-1 and IEC 601-
2-10 (general and particular standards) requirements.

The Dynatron 150plus allows you to combine electrical stim therapy with Ultrasound
therapy. The device accepts input from electrotherapy devices through the Stim Input
jack found on the back of the device. This jack accommodates a banana adapter (a
pin-to-banana adapter is attached to one output end of a patient lead).

The following instructions explain how to use the Dynatron 150plus with
Dynatronics’ electrotherapy devices. With this type of treatment, the soundhead acts
as one of the electrodes in a 2-electrode stim treatment, and stim is delivered through
the soundhead. See “Usage Cautions - Combination Treatments” in this manual
before using this option.

1. Plug a patient lead into one channel of the Dynatron electrotherapy device. Use a

single lead with two output connectors.

Place a pin-to-banana adapter on one output end of the lead, then plug that banana
adapter into Stim Input jack on the back of the Dynatron 150plus. NOTE: If you
do not have a pin-to banana adapter, contact Dynatronics to order.

Attach the other lead output to an electrode (use an electrode that you normally
use with your Dynatron electrotherapy device) and place the electrode in the
desired location on the patient’s body. The electrode should be placed slightly
outside the area where the Ultrasound will be delivered to allow full movement of
the soundhead over the treatment area. Remember the soundhead delivers Stim
as well as Ultrasound during the treatment, and therefore, the soundhead acts as
the second electrode. Consider this when you determine where to place the
electrode and the soundhead on the patient.

2. Set up an Ultrasound treatment with the Dynatron 150plus. Do not press START.

3. Set up the Stim treatment for the appropriate channel on the Dynatron

electrotherapy device. Use a very low stim intensity for this type of treatment.

4. START the treatments at both devices.

During the treatment, the Stim current is delivered through the soundhead and will
pass between the soundhead and the electrode which was placed on the patient. At
the same time ultrasonic waves are introduced into patient tissue through the
soundhead. Avoid touching the electrode with the soundhead during the treatment,
and keep the Stim intensity low.

«
...
21
22
23
24
25
...
»

Содержание 150plus


































































Отзывы:

Нет отзывов

Похожие инструкции для 150plus

Бренд: MacDon Страницы: 272

Бренд: MacDon Страницы: 70

Бренд: NEC Страницы: 44

Бренд: Fellowes Страницы: 20

Бренд: Garmin Страницы: 10

Бренд: Naviom Страницы: 31

Бренд: Nel-Tech Labs Страницы: 8

Бренд: quadient Страницы: 188

Бренд: Radarsign Страницы: 16

Бренд: Cannon Страницы: 70

Бренд: ACS Страницы: 28

INTRAmatic 31 ES

Бренд: KaVo Страницы: 52

Бренд: ABB Страницы: 106

Бренд: Gardol Страницы: 80

MS-1 MICRO SEQUENCER - MUSICIAN S GUIDE

Бренд: Kurzweil Страницы: 91

Бренд: schmersal Страницы: 20

Бренд: Boss Audio Systems Страницы: 7

Бренд: Dr.X Works Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды