Dynapac V5100TV-H Скачать руководство пользователя страница 156

Страница: 156 / 196

F 20

8.2

Adjusting the ignition burner

To ensure proper ignition, the adjusting

ring (1) of the ignition burner must be ad-
justed.

- Loosen the fastening screws of the

adjusting ring.

- The adjusting ring (1) should cover

roughly 50% of the air holes (2).

- Tighten the fastening screws of the

adjusting ring again.

8.3

Injectors of the gas heater system

The injectors for preparing the gas/air
mixture are not subject to any mainte-
nance intervals.

Impurities in the propane gas may soil
the filter.

In this case, unscrew the screwed fitting

(3) and then the gas nozzle (4). The filter
is connected with the gas nozzle. Care-
fully clean the filter using air.

Never use a pointed object to clean the

gas nozzle and the filter since this could

damage the filter or the bore hole of the

gas nozzle.

The screwed fitting (3) and the gas noz-
zle (4) have been glued-in at the factory

using "Loctite blue".

After cleaning, glue in the gas nozzle (4)
and the screwed fitting (3) and screw

them down.

Make sure that all gas pipe connections
are firmly screwed together.

Danger of explosions in case of leaks.

Содержание V5100TV-H





































































































































































































Результаты поиска

Содержание V5100TV-H

Отзывы:

Похожие инструкции для V5100TV-H

Бренды по названию

Популярные бренды

Dynapac V5100TV-H, Приложение, эксплуатация и обслуживание

Результаты поиска

Содержание V5100TV-H

Отзывы:

Похожие инструкции для V5100TV-H

Бренды по названию

Популярные бренды