Dynapac V5100TV-H Скачать руководство пользователя страница 137

Страница: 137 / 196

F 1

F Maintenance

Notes regarding safety

Danger due to changes at the vehicle

Structural chances to the vehicle make the operating
licence null and void and can cause severe to fatal injuries!

- Only use original spare parts and approved accessories.
- After maintenance and repair work, ensure that any dis-

mantled protective and safety devices are all completely
fitted again.

- Comply with all further information in these instructions

and in the safety manual.

Danger due to incorrect vehicle maintenance

Incorrectly performed maintenance and repair work can
cause severe or fatal injuries!

- Ensure that maintenance and repair work is always only

carried out by trained, specialist staff.

- All maintenance, repair and cleaning work should only

be carried out with the engine turned off. Remove igni-
tion key and main switch.

- Affix a sign "Do not start" to the vehicle.
- Perform a visual inspection and check all functions

every day.

- Proceed with all maintenance tasks according to the

maintenance schedule.

- Proceed with expert inspection every twelve months.
- Eliminate all ascertained faults straight away.
- Do not restart the vehicle until all ascertained faults have

been eliminated.

- Failure to comply with the prescribed inspection and

maintenance work renders the operating licence null

and void!

- Comply with all further information in these instructions

and in the safety manual.

DANGER

Содержание V5100TV-H





































































































































































































Результаты поиска

Содержание V5100TV-H

Отзывы:

Похожие инструкции для V5100TV-H

Бренды по названию

Популярные бренды

Dynapac V5100TV-H, Приложение, эксплуатация и обслуживание

Результаты поиска

Содержание V5100TV-H

Отзывы:

Похожие инструкции для V5100TV-H

Бренды по названию

Популярные бренды