manualshive.com logo in svg

Dux 28ENR6L, Руководство по установке, Страница: 35 / 36

Поделиться
Скачать
Dux 28ENR6L Скачать руководство пользователя страница 35

35

Installation Manual

Storage Tank Circulation pump 2

Storage Tank Circulation pump 1

Relief valve

Hot water  supply points

Hot water supply line

Hot water return line

Cold water supply pipe *1

When installing 2 pumps in parallel

Set “Yes” for the question 

“Start pump rotation?” in system settings.

(See SCU-401-12M Installation Manual)

*  Size the cold water supply piping to allow for 

    maximum flow rates of the building.

*  Be sure to connect the cold water supply pipe 

    between the hot water storage tank and intake 

    side of the storage tank circulation pump.

Thermostat

System Controller Unit

Remote 

controller 

cord

Remote Controller

Pump control

(use external relays)

Unit 1

Unit 2

Unit 3

Unit 10

Unit 11

Unit 12

(copper or stainless steel pipe)

Hot water

storage tank

(copper or stainless steel pipe)

Return line  circulation pump

(Size for max. flow)

(Size for max. flow)

Storage tank supply line (copper or stainless steel pipe)

Storage tank return line (copper or stainless steel pipe)

B-2. Example of Installation with a Storage Tank and Recirculation System (Using external system controller) 

The pump will push water through the Multi-System to heat up the tank.
When the temperature of the thermostat is high, the system controller will turn off the pump until the 
temperature cools down.

* 

For the set temperatur

e of the r

emote contr

oller

, use the temperatur

e (of the thermostat) + about 5 °C.

* 

To

 achieve the highest r

ecovery

, size the storage tank cir

culation pump for maximum capacity

. 

  

(32ECR6 : 34 L/min (each) @ 12 m of head, 28ENR6 : 26 L/min (each) @ 10 m of head (75 °C setting or less) + 

    piping losses thr

ough the system.) 

 

V

erify the supply pr

essur

e to the units is at least 200 Kpa.

 (Tank recirculation system)

SBB80RW̲P001-P036̲E.indd   35

SBB80RW̲P001-P036̲E.indd   35

2016/10/03   18:29:47

2016/10/03   18:29:47

Содержание 28ENR6L





































Отзывы:

Нет отзывов