manualshive.com logo in svg

Dux 28ENR6L, Руководство по установке, Страница: 18 / 36

Поделиться
Скачать
Dux 28ENR6L Скачать руководство пользователя страница 18

18

Installation   Manual

Drain processing

•  Expansion water may drop from the pressure relief valve and wet the fl oor. 

Hot water piping

• Do not use lead, PVC, iron or any piping which has been treated with chromates, boiler seal or other 

chemicals.

• Keep the pipe lengths to a minimum, and make sure that the pipework is well insulated as correct 

performance of the appliance is dependent on properly insulated pipework.

•  DO NOT FIT ANY VALVES OR RESTRICTORS TO THE OUTLET OF THE WATER HEATER.
• DO NOT FIT ANY OBSTRUCTION TO THE PRESSURE RELIEF LOCATED ON THE HOT WATER OUTLET 

CONNECTION.

•  Use mixing valves with low water resistance. Use shower heads with low pressure loss.
•  If necessary, use a pump or other means to ensure that the supply water pressure to the inlet of the heater 

does not fall below 199kPa when the maximum amount of water is being demanded. If the water pressure 
drops below 200 kPa, local boiling can occur inside the water heater causing abnormal sounds and 
decreasing the durability of the heat exchanger.

After purging the air from the system using the hot water supply taps, remove the water inlet strainer located 
on the cold water supply inlet connection.  Remove any debris from the fi lter and replace.  When replacing the 
fi lter, do not over-tighten the “O” ring seal.

No pressure reduction is required unless the water pressure exceeds 1000kPa.

SBB80RW̲P001-P036̲E.indd   18

SBB80RW̲P001-P036̲E.indd   18

2016/10/03   18:29:43

2016/10/03   18:29:43

Содержание 28ENR6L





































Отзывы:

Нет отзывов