Dux 28ENR6L Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 36

Dux 28ENR6L Скачать руководство пользователя страница 13

13

Installation Manual

Before installing, check for the following:

The location of the ﬂ ue terminal must comply with the clearances shown on this page. If you are
unsure about clearances not indicated here, in general refer to AS/NZS5601, or your local authority. In
Western Australia refer to the WA Ofﬁ ce of Energy rules and regulations.

Flue outlet must be free from any combustible material.

WARNING

• Install the water heater in a location where it is free from obstacles and

stagnant air.

• Consult with the customer concerning the location of installation.

• Do not install the water heater near staircases or emergency exits.

• Do not install the water heater where the exhaust will blow on outer walls

or material not resistant to heat. Also consider the surrounding trees and
animals.

The heat and moisture from the water heater may cause discoloration of
walls and resinous materials, or corrosion of aluminium materials.

• Do not locate the vent termination directed towards a window or any other

structure which has glass or wired glass facing the termination.

• Install in a location where the exhaust gas ﬂ ow will not be affected by fans

or range hoods.

• Take care that noise and exhaust gas will not affect neighbours.

• Avoid installation where the unit will be exposed to excessive winds.

• Before installing, make sure that the vent termination will have the proper

clearances according to AS/NZS5601, or your local authority.

• On combustible surfaces e.g. weatherboards etc. it is not required to install

a ﬁ re proof back board.

CAUTION

Prohibited

Installation Clearances

SBB80RW̲P001-P036̲E.indd 13

SBB80RW̲P001-P036̲E.indd 13

2016/10/03 18:29:42

2016/10/03 18:29:42

«
...
11
12
13
14
15
...
»

Содержание 28ENR6L





































Отзывы:

Нет отзывов