Dux 28ENR6L Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 36

Dux 28ENR6L Скачать руководство пользователя страница 22

22

Installation Manual

To ensure compliance with Australian Standard AS/NZS3500.4, for sanitary areas, install the water heater with a
tempering valve. In New Zealand, please refer to the New Zealand Building Code and all other applicable electrical, gas
ﬁ tting and plumbing codes.

<The changing procedure of the maximum temperature setting.>
1. Turn the water heater off by pressing the ON/OFF button on the remote controller.

2. Disconnect electrical power to the water heater.

3. Remove the front cover of the water heater (4 screws).
4. Adjust the dip switches as illustrated below.
5. Replace the front cover of the water heater (4 screws).
6. Reconnect electrical power to the water heater.

Applicable Model

* Maximum temperature is controlled by the maximum default temperature set in the water heater.

* Only one the remote controller can be connected to the water heater.
A malfunction may occur if two or more remote controllers are connected.

The maximum temperature allowed can be changed with adjusting the dip switches as described below.

Remote Controller

Remote controller

RC-9018C

Max temperature 85°C *

* Do not change any other dipswitches.

* Maximum temperature.

1

2

ON=

OFF=

85 C

55 C

75 C

85 C

Check

Check

SBB80RW̲P001-P036̲E.indd 22

SBB80RW̲P001-P036̲E.indd 22

2016/10/03 18:29:44

2016/10/03 18:29:44

«
...
20
21
22
23
24
...
»

Содержание 28ENR6L





































Отзывы:

Нет отзывов