Dux 28ENR6L Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 36

Dux 28ENR6L Скачать руководство пользователя страница 15

15

Installation Manual

Illustration

Check

4. Drill holes for the remaining four screws.

5. Hang the unit again by the ﬁ rst screw, and then

insert and tighten the remaining four screws.

6. Take waterprooﬁ ng measures so that water does

not enter the building from screws mounting the
device.

• Make sure the unit is installed securely so that it will

not fall or move due to vibrations or earthquakes.

Securing to the wall

1. Drill a single screw hole, making sure to hit a stud.

2. Insert and tighten the screw and hang the unit by

the upper wall mounting bracket.

3. Determine the positions for the remaining four screws

(two for the top bracket and two for the bottom), and
remove the unit.

• Installation must conform with all local building, water and Gas Regulations and AS/NZS5601.
• The weight of the device will be applied to the wall. If the strength of the wall is not sufﬁ cient,

reinforcement must be done to prevent the transfer of vibration.

• Do not drop or apply unnecessary force to the device when installing. Internal parts may be

damaged and may become highly dangerous.

• Install the unit on a vertical wall and ensure that it is level.
• Insure no additional pressure is applied to the pipework.

Locating Scr

ew Holes

Mounting

Structur

e

• When installing with bare hands, take caution to not

inﬂ ict injury.

• Be careful not to hit electrical wiring, gas, or water

piping while drilling holes.

Item

CAUTION

Be sure to do

Mounting Bracket
(upper)

Anchoring Screw

Location of Screw Hole

Locating Screw Holes

Installation

SBB80RW̲P001-P036̲E.indd 15

SBB80RW̲P001-P036̲E.indd 15

2016/10/03 18:29:43

2016/10/03 18:29:43

«
...
13
14
15
16
17
...
»

Содержание 28ENR6L





































Отзывы:

Нет отзывов