Dux 28ENR6L Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 36

Dux 28ENR6L Скачать руководство пользователя страница 12

12

Installation Manual

* Locate the appliance in an area where water leakage from the unit or connections will not result in

damage to the area adjacent to the appliance or to the lower ﬂ oors of the structure. When such locations
cannot be avoided, it is recommended that a suitable drain pan, adequately drained, be installed under
the appliance. The pan must not restrict combustion air ﬂ ow.

DANGER

Indoor

• This water heater is for outdoor installation only.

Never install it indoors.

Do not enclose the termination with corrugated

metal or other materials.

This will cause carbon monoxide
poisoning and a potential ﬁ re
hazard.

Prohibited

WARNING

Choosing an Installation Site

• Avoid places where ﬁ res are common, such as those where petrol,

benzene and adhesives are handled, or places in which corrosive gases
(ammonia, chlorine, sulfur, ethylene compounds, acids) are present.

May result in ﬁ re.

• Avoid installation in places where dust or debris will accumulate.
Dust may block the air-supply opening, causing the performance of the

device fan to drop and incomplete combustion to occur as a result.

• Avoid installation in places where special chemical agents

(e.g., hair spray or spray detergent) are used.

Ignition failures and malfunction may occur as a result.

• Carbon Monoxide Poisoning Hazard. Do not install this water heater in a

mobile home, recreation vehicle or on a boat.

• Leave the proper clearance between the water heater and nearby

objects (trees, timber, boxes with ﬂ ammable materials etc.).

Upper:
Min. 500mm

Right side:
Min. 500mm

Left side:
Min. 500mm

Front:
Sug. 600mm

SBB80RW̲P001-P036̲E.indd 12

SBB80RW̲P001-P036̲E.indd 12

2016/10/03 18:29:42

2016/10/03 18:29:42

«
...
10
11
12
13
14
...
»

Содержание 28ENR6L





































Отзывы:

Нет отзывов