Dux 28ENR6L Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 36

Dux 28ENR6L Скачать руководство пользователя страница 10

10

Installation Manual

Do Not Use Equipment for Purposes Other Than Those Specifi ed

• Do not use for other than increasing the temperature of the water supply, as unexpected accidents

may occur as a result.

Check Water Supply Quality

• If the water supply is hard, acidic or otherwise impure, treat the water with approved methods in

order to ensure full warranty coverage.

See water quality statement on page 28.

Frost Protection

• When installed, power to the unit must be kept switched on, otherwise the appliance should be

drained.

This prevents water freezing, and causing damage to the water heater.

WARNING

CAUTION

For NG Gas

Before Installation

xx

xxxxxxxx

xx

xx

xx

xx

Check the Gas

•  Check that the data label (Side of casing).
•  Check that the gas supply line is sized for
  32ECR6N, 32ECR6L: 217 MJ/hr, 217 MJ/hr
  28ENR6N, 28ENR6L: 220 MJ/hr, 220 MJ/hr

• DO NOT OPERATE WITH ANY OTHER GAS TYPE.

Check the Power

• The power supply required is 230 - 240VAC, at 50Hz.
Using the incorrect voltage may result in ﬁ re or
electric

shock.

Warning labels

• Located on the side of the casing -PLEASE READ THESE LABELS CAREFULLY!

SBB80RW̲P001-P036̲E.indd 10

SBB80RW̲P001-P036̲E.indd 10

2016/10/03 18:29:41

2016/10/03 18:29:41

«
...
8
9
10
11
12
...
»

Содержание 28ENR6L





































Отзывы:

Нет отзывов