Dux 28ENR6L Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 36

Dux 28ENR6L Скачать руководство пользователя страница 20

20

Installation Manual

Slope pipe downwards
1/50

The end of the drain pipe
must have an air gap.

The end of the drain pipe
must have an air gap.

Condensate piping to floor drain

Slope pipe downwards
1/50

1/2" PVC pipe

1/2" PVC elbow

3/8" ID tubing*

* Install tubing according to pump
manufacturer's instructions.

Condensate piping with pump

Condensate pump

Floor drain

MAINTAIN CLEARANCE

1/2" PVC pipe

DO NOT ADD
ANY VALVES

Condensing

Tankless Gas

Water Heater

Condensing

Tankless Gas

Water Heater

DO NOT ADD
ANY VALVES

Note:
If the drain line becomes clogged or frozen, condensate will back-up into the water heater and a "29" error
code will ﬂ ash on the remote controller, ceasing operation. If this occurs, clear the clog or freeze so that
condensate can freely ﬂ ow. Be sure to slope the drain pipe, use the appropriate size pipe, allow the proper
clearances, and apply freeze prevention measures (when necessary) to prevent the drain line from clogging
or freezing.

SBB80RW̲P001-P036̲E.indd 20

SBB80RW̲P001-P036̲E.indd 20

2016/10/03 18:29:44

2016/10/03 18:29:44

«
...
18
19
20
21
22
...
»

Содержание 28ENR6L





































Отзывы:

Нет отзывов