manualshive.com logo in svg

Dux 28ENR6L, Руководство по установке, Страница: 28 / 36

Поделиться
Скачать
Dux 28ENR6L Скачать руководство пользователя страница 28

28

Installation   Manual

WATER QUALITY 

All Dux water heating appliances are constructed from high quality materials and 
components and all are certifi ed for compliance with relevant parts of Australian and New 
Zealand gas, electrical and water standards.

Whilst Dux water heaters are warranted against defects, the warranty is conditional upon 
correct installation and use, in accordance with detailed instructions provided with the 
heater. In the case of the water supplied to the heater, it is important that the water quality 
be of acceptable standard.

The water quality limits/parameters listed in water quality table are considered acceptable 
and generally, Australian and New Zealand suburban water supplies fall within these 
limits/parameters.

In areas of Australia and New Zealand where water may be supplied, either fully or partly, 
from bores, artesian wells or similar, one or more of the important limits may well be 
exceeded and the heater could, therefore, be at risk of failure.

Where uncertainty exists concerning water quality, intending appliance users should seek 
a water analysis from the water supplying authority and in cases where it is established 
that the water supply does not meet the quality requirements of the water quality table, 
the Dux warranty would not apply.

WATER QUALITY TABLE 

Maximum levels

   pH 

Saturation  

Total  

Chlorides 

Sodium 

Iron

 Index(LSI) 

Hardness 

 (langelier) 

   6.5-9 

+0.4 to 

200mg/l 

250mg/l 

180mg/l 

1mg/l

 Minus 

1.0

 @65C

SBB80RW̲P001-P036̲E.indd   28

SBB80RW̲P001-P036̲E.indd   28

2016/10/03   18:29:46

2016/10/03   18:29:46

Содержание 28ENR6L





































Отзывы:

Нет отзывов