Dux 28ENR6L Скачать руководство пользователя страница 21

21

Installation Manual

• The appliance is equipped with a 1.5m cable with a three pinned earthed plug to be connected to 

230

 - 

240VAC at 50 Hz. 

  The power consumption may be up to 32ECR6 series 223W, 28ENR6 series 193W.
  Use an appropriate circuit.
• The appliance requires a 240V in Australia and 230V in New Zealand, 50Hz weatherproof plug in-

stalled in a protected position adjacent to the appliance.

• If the power cord is damaged and requires replacement, use only an original spare part available from 

the manufacturer.

• Do not disconnect the power supply when not in use. When the power is off, the freeze prevention in 

the water heater will not activate, resulting in possible freezing damage.

• Do not let the power cord contact the gas piping.

Tie the excess power cord outside the water heater. Putting the redundant length of cord inside 
the water heater may cause electrical interference and faulty operation.

Electrical Shock Hazard
Do not turn power on until controllers have been connected. Disconnect power before servicing.
 

Failure to do so may result in death or serious injury from electrical shock.

WARNING

Electrostatic discharge can affect electronic components. Take precautions to prevent electrostatic dis-
charges from personnel or hand tools during the water heater installation and servicing to protect prod-
uct’s electronic control.

CAUTION

Earth

• To prevent electrical shock, always plug power lead into an earthed point.

Electrical Wiring

SBB80RW̲P001-P036̲E.indd   21

SBB80RW̲P001-P036̲E.indd   21

2016/10/03   18:29:44

2016/10/03   18:29:44

Содержание 28ENR6L





































Отзывы: