Dux 28ENR6L Скачать руководство пользователя страница 3

Страница: 3 / 36

Installation Manual

Potential dangers from accidents during installation and use are divided into the following
three categories. Closely observe these warnings, they are critical to your safety.

Prohibited

Earth

Requests to Installers

• In order to use the water heater safely, read this installation manual carefully, and follow the

installation instructions.

• Failures and damage caused by erroneous work or work not as instructed in this manual are not

covered by the warranty.

• Check that the installation was done properly in accordance with this Installation Manual upon

completion.

• After completing installation, please either place this Installation Manual in a plastic pouch and

attach it to the side of the water heater, or hand it to the customer to retain for future reference.

WARNING:

CAUTION

• The water heater must be commissioned including checking gas supply pressures at maximum

demand.

• The operation of the water heater should be explained including normal operation & regular

maintenance.

CAUTION

Condensing Models

Non Condensing Models

32ECR6N
32ECR6L

28ENR6N
28ENR6L

DANGER indicates an imminently hazardous situation which,
if not avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.

WARNING

CAUTION

DANGER

SBB80RW̲P001-P036̲E.indd 3

2016/10/03 18:29:39

Содержание 28ENR6L





































Результаты поиска

Содержание 28ENR6L

Отзывы:

Dux 28ENR6L, Руководство по установке, Страница: 3 / 36

Результаты поиска

Содержание 28ENR6L

Отзывы: