Dux 28ENR6L Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 36

Dux 28ENR6L Скачать руководство пользователя страница 1

Installation

Manual

To be installed and serviced only by an authorised person.

This appliance is not suitable for use as a pool heater.

The "authorised installing person" is responsible for:
1. Correct commissioning of this appliance
2. Ensure unit performs to the specification stated on the data label
3. Demonstrate operation of unit to customer before leaving
4. Hand these instructions to customer

This appliance must be installed in accordance with the manufacturer's installation instructions all Local Building,
Water and Gas fitting regulations (AS/NZS3500.4, AS/NZS 5601, AS/NZS3000).

This appliance delivers water in ex cess of 50 DegreeC.Ensur that suitab li devices such as Tempering Valves are
installed in lines servicing Sanitation areas per AS3500.4.

Failure to install this appliance in accordance with these installation instructions may void warranty.

In the interest of continued product improvement, Dux Manufacturing reserves the right to alter these specifications
without notice.

SBB80RW
Rev. 10/16

*SBB80RW*

AU Service Department : 1300 365 115
NZ Service Department : 0800 729 389

Ex. 32ECR6N

Condensing Models

32ECR6N
32ECR6L

Non Condensing Models

28ENR6N
28ENR6L

SBB80RW̲P001-P036̲E.indd 1

SBB80RW̲P001-P036̲E.indd 1

2016/10/03 18:29:39

2016/10/03 18:29:39

1
2
3
...
»

Содержание 28ENR6L





































Отзывы:

Нет отзывов