DriSteem Vaporstream Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 80

background image

21

VAPORSTREAM INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

• Keypad/display with standard 5' (1.5 m) cable ships mounted to subpanel in Outdoor

Enclosure. Keypad/display must not come in contact with strip heaters or block intake ventilation
hood.

• If constant monitoring of unit is desired, or if unit is located in a severe climate, a remote-mount

keypad/display should be installed. Additional cable lengths up to 500 feet (152 m) are
available as an option for this mounting conﬁ guration.

• 16-gauge galvanized steel curbs (optional) are shipped unassembled for ease of transporting

to roof; they include all hardware for bolt-together assembly, and all holes are matched before
leaving factory. Curb must be a minimum of 14" (356 mm) high. One 2" × ½" closed-cell curb
gasket with adhesive on one side is supplied with hardware. Gasket must be installed between
top of curb and base surface of Outdoor Enclosure to prevent moisture from leaking into
building from driving rain or melting snow. Installation drawing is included.

• Four symmetrically shaped stand legs (optional) are include all necessary hardware for elevating

Outdoor Enclosure 14" (356 mm) from ground. Stand legs should be securely mounted to grade
by installing contractor. To prevent outdoor environment from penetrating enclosure, close-off
provisions must be made between stand legs.

• All piping from humidiﬁ er to steam outlet is stainless steel pipe. Depending on application,

interconnecting piping from steam outlet to dispersion assembly can be DriSteem steam hose or
tubing.

Outdoor Enclosure:

Steam piping

Roof surface

Curb

Water piping

Remote Vapor-logic keypad

Electrical con nec tions

OM-7609

Drain piping

Humidiﬁ er in Outdoor Enclosure

INSTALLATION

FIGURE 21-1: TYPICAL ROOFTOP INSTALLATION OVERVIEW

Mounting

«
...
23
24
25
26
27
...
»

Содержание Vaporstream

















































































Отзывы:

Нет отзывов

Похожие инструкции для Vaporstream

Бренд: Lasko Страницы: 2

Бренд: GMC Страницы: 20

Бренд: German pool Страницы: 16

Бренд: Easylife Страницы: 3

Бренд: Ebac Страницы: 11

Бренд: Suki Страницы: 11

Бренд: Fortress Technologies Страницы: 13

AQUARIA SLIM 10 P

Бренд: Olimpia splendid Страницы: 148

Бренд: AMW Страницы: 31

Бренд: Ebac Страницы: 6

Бренд: Ebac Страницы: 13

Бренд: weewell Страницы: 32

Бренд: Beurer Страницы: 84

Бренд: Air-O-Swiss Страницы: 64

Бренд: Mitsubishi Страницы: 52

Бренд: Stadler Form Страницы: 56

Бренд: Stylies Страницы: 106

LEONIS ULTRASCHALL

Бренд: Stylies Страницы: 105

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды