DriSteem Vaporstream Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 80

background image

19

VAPORSTREAM INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Outdoor Enclosure:

• Outdoor Enclosure must be level and located so there is enough clearance

for opening access doors.

• Verify that position of support legs, pad, or curb properly support unit, and

support structure dimensions coincide with unit dimensions.

• Locate unit so air intakes are not too close to exhaust fan outlets, gasoline

storage, or other contaminants that could cause dangerous situations.
Using and storing gasoline or other ﬂ ammable vapors and liquids in open
containers in the vicinity of this appliance is hazardous.

• When located on roof, Outdoor Enclosure air intakes must be a minimum

of 14" (356 mm) above roof to prevent intake of snow or splashed rain.
Locate Outdoor Enclosure so prevailing winds do not blow into air intakes.

• Remove all shipping brackets and other packaging prior to installing

Outdoor Enclosure.

• During transit, unloading, and setting of unit, bolts and nuts may have

become loosened. Check that all nuts are tightened.

• There are four knockouts on the right and left side of the enclosure. It is

recommended that electrical power is run into enclosure at these knockouts.

• Outdoor Enclosure is designed for lifting by two methods:

– Preferred method of lifting is by forklift. This is only possible if the forks

extend across entire unit. Forks that do not extend across entire unit
could cause tipping, resulting in unsafe conditions or damage to the
unit.

– Alternative method of lifting is through unit’s channel base frame and/

or special lifting lug hooks installed on the unit. Use a load spreader of
sufﬁ cient width to ensure that lifting cables clear sides of unit. If such a
spreader is not available, insert wood strips between cables and unit
where necessary. All four lifting points must be used; they are marked
“lift here” on the unit.

In both cases it must be lifted from the bottom base and kept level, and
it must not tip, fall, or twist. If unit is severely twisted during handling,
permanent damage could occur. It is installer’s responsibility to verify
handling equipment’s capability to safely handle Outdoor Enclosure.

DC-1110

Flush

14" (356 mm)

OM-1095

Curb

INSTALLATION

FIGURE 19-1: OUTDOOR ENCLOSURE
MOUNTING OPTIONS

Mounting

«
...
21
22
23
24
25
...
»

Содержание Vaporstream

















































































Отзывы:

Нет отзывов

Похожие инструкции для Vaporstream

Бренд: TCS Страницы: 8

Бренд: Eco Air Страницы: 17

Бренд: Hunter Страницы: 2

Бренд: GMC Страницы: 20

Бренд: German pool Страницы: 16

23-11-2242N-005

Бренд: Maytag Страницы: 16

Airtek SMART CYCLE PLUS 100

Бренд: Parker Страницы: 45

Бренд: EdgeStar Страницы: 16

Бренд: Aircare Страницы: 33

Бренд: GeneralAire Страницы: 2

Бренд: Livart Страницы: 6

DRYPOINT RA CT 100-NA-EB

Бренд: Beko Страницы: 76

DRYPOINT RA 1000/AC NA

Бренд: Beko Страницы: 52

DRYPOINT RA HT 100-P NA UL

Бренд: Beko Страницы: 52

Бренд: SAN-UP Страницы: 12

V425 - Vicks Nursery 1.2G Humidifier

Бренд: Kaz Страницы: 2

Бренд: NORPOLE Страницы: 26

Бренд: Trion Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды