DriSteem Vaporstream Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 80

background image

12

VAPORSTREAM INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

DriSteem
optional wall
brackets (two
required)

A

24.75" (629 mm)

Table 12-1:
Wall brackets Dimension A
(center to center of mounting holes)

Vaporstream model

inches

mm

One-heater models:
2-1, 3-1, 4-1, 5-1

17

432

Three-heater models:
6-1, 9-1, 12-1,
16-1, 21-1, 25-1

17

432

Six-heater models:
12-2, 18-2, 24-2,
32-2, 42-2, 50-2

17

432

Nine-heater models*:
18-3, 27-3, 36-3,
48-3, 63-3, 75-3

28

711

Twelve-heater models*:
24-4, 36-4, 48-4,
64-4, 84-4, 100-4

34

864

*

Wall bracket installation on metal stud walls
is not recommended for nine-heater and
twelve-heater models

mc_022310_1345

VLC-OM-007

Mounting:

DriSteem recommends using 3/8" (M10) fasteners.

• Wood stud wall, recommended mounting — two horizontal 2 × 4s (100

mm × 50 mm timbers) with center line spaced at dimension shown in Table
12-1.

– Three-heater models: lag bolt (coach screw) both horizontal 2 × 4s (100

mm × 50 mm timbers) to two vertical studs (16"
[404 mm] on center)

– Six-heater and nine-heater models: lag bolt (coach screw) to three studs

– 12-heater models: lag bolt (coach screw) to four studs

Lag bolt (coach screw) wall brackets to the horizontal 2 × 4s
(100 mm × 50 mm timbers). Locate the wall brackets so they are ﬂ ush to
the front and back ﬂ anges of the tank.

• Metal stud wall — follow the same 2 × 4 wood stud (100 mm × 50 mm

timber) wall guidelines, but provide a second set of 2 × 4s (100 mm × 50
mm timbers) on the backside of the wall. Run a bolt with a washer through
the face 2 × 4 (100 mm × 50 mm timber), the metal stud, and the backside
2 × 4 (100 mm × 50 mm timber) with washer and nut to connect the 2 × 4s
(100 mm × 50 mm timbers). DriSteem does not recommend mounting the
nine-heater and 12-heater models on a metal stud wall — use support legs.

• Concrete or block walls — use concrete anchors (expansion bolts) rated for

the operating weight of the Vaporstream humidiﬁ er. Locate the wall brackets
so they are ﬂ ush to the front and back ﬂ anges of the tank.

Shim or adjust mounting so the tank sets level from side to side and front to
back. Verify level after the tank is ﬁ lled and is at operating weight.

INSTALLATION

FIGURE 12-1: WALL BRACKETS

Wall brackets

«
...
14
15
16
17
18
...
»

Содержание Vaporstream

















































































Отзывы:

Нет отзывов

Похожие инструкции для Vaporstream

Бренд: Uberhaus Страницы: 22

Бренд: Dometic Страницы: 28

Бренд: Sinbo Страницы: 48

Бренд: Neptronic Страницы: 28

HUMBLBP-17H6--A

Бренд: Bosch Страницы: 16

Бренд: BRAYER Страницы: 32

Herrmidifier G100

Бренд: Trion Страницы: 2

Бренд: Trion Страницы: 2

Бренд: ECG Страницы: 52

Бренд: camry Страницы: 80

Бренд: Munters Страницы: 44

Бренд: Romus Страницы: 20

Бренд: Noaton Страницы: 121

Бренд: Nortec Страницы: 70

Бренд: Objecto Страницы: 17

easy dry compact

Бренд: SOLIS Страницы: 32

Бренд: LivePure Страницы: 12

Бренд: Nortec Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды