DriSteem Vaporstream Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 80

background image

65

VAPORSTREAM INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Tap/softened water:

MAINTENANCE

Humidifier De-scaling Solution

Scale buildup on humidiﬁ er heaters acts as
an insulator, reducing humidiﬁ er performance
while increasing energy costs. To keep
humidiﬁ ers operating as efﬁ ciently as possible,
remove scale with DriSteem's Humidiﬁ er De-
scaling Solution, available for purchase from
your DriSteem representative or distributor.

The De-scaling Solution cleans without risk
of corroding humidiﬁ er tanks or welds. The
De-scaling Solution also cleans surfaces
unreachable by hand scraping.

DriSteem's Humidiﬁ er De-scaling Solution is the
only approved cleaner/de-scaler for use with
DriSteem humidiﬁ ers. Use of other cleaners/de-
scalers may void your DriSteem warranty.

mc_021908_1410

• Cleaning the skim/overﬂ ow port

–

Water should drain from the skimmer drain pipe after each ﬁ ll cycle.
This should be veriﬁ ed visually by a weekly inspection.

–

Loosen deposits in and around the skimmer/overﬂ ow port with a
long tool such as a screwdriver.

–

If ﬂ ow through the water seal/P-trap is diminished due to mineral
accumulation:

– Remove the water seal piping from the hu mid i ﬁ er and ﬂ ush out.

– Replace the water seal with new piping if the minerals have

hardened in the water seal.

– Install a union at the base of the water seal to ease removal if

water quality causes the water seal to become clogged often with
scale.

• When the maintenance requirements are complete:

– Slide the cleanout tray back into the tank.

–

Hook the tab on the backside of the cleanout plate over the edge of
the cleanout tray and slide the cleanout plate over the tank studs.

–

Torque the cleanout plate nuts to 25 to 35 in-lb (2.8 to 4.0 N-m).

–

Verify that the probe rod holder is secure and that the probe plug
and cable assembly are plugged into the probe rod holder.

– Replace and secure all covers and doors.

–

Verify that the drain valve assembly is in the closed position.

– Turn on the water supply.

– Turn on the electrical power.

–

Do not leave humidiﬁ er unattended. Allow the hu mid i ﬁ er to cycle
through multiple ﬁ ll cycles and verify that the humidiﬁ er cover,
cleanout plate, and probe holder gasket are not leaking.

3.

Off-season maintenance

• Perform complete inspection and cleaning of the following:

– Heaters

– Probe

rods

– Skimmer port and water seal

– Humidiﬁ er tank

•

After cleaning, the humidiﬁ er should remain empty until humidiﬁ cation is
required.

Inspection and maintenance

«
...
67
68
69
70
71
...
»

Содержание Vaporstream

















































































Отзывы:

Нет отзывов

Похожие инструкции для Vaporstream

Бренд: Salter Labs Страницы: 2

Бренд: GE Страницы: 24

Бренд: GE Страницы: 36

Бренд: ACD Страницы: 24

KLIMATRONIC Monsun 2.500 moodlight

Бренд: Suntec Wellness Страницы: 105

Бренд: Trion Страницы: 16

Бренд: Easy@Home Страницы: 21

Бренд: Vornado Страницы: 20

SPX Flow FLEX Series

Бренд: HANKISON Страницы: 26

Бренд: Lasko Страницы: 12

Бренд: Germ Guardian Страницы: 18

Бренд: paasche Страницы: 2

Бренд: Ultra-air Страницы: 20

Бренд: Fortress Technologies Страницы: 13

Бренд: Frigidaire Страницы: 7

Бренд: Frigidaire Страницы: 9

Бренд: Frigidaire Страницы: 10

Бренд: Frigidaire Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды