DriSteem Vaporstream Скачать руководство пользователя страница 48

Страница: 48 / 80

VAPORSTREAM INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Dispersion tube plate

Condensate drain plate

90° long sweep or two
45° elbows

Vaporstream humidiﬁ er

2" (51 mm) minimum

Water seal

5" (127 mm)

Pitch

(see Note 2 below)

1" (25 mm) air gap

Open drain required. See Note 1 below.

Condensate drain tube, by installer, minimum ¾" (DN20);
must be suitable for 212 °F (100 °C) water

½" (DN15) O.D. condensate drain
tube; pitch ¼"/ft (2%)

Pitch tube toward
drain 1/8"/ft (1%)

3/8" (M10)
mounting nut

Duct

¼" (DN8)
pipe thread

Notes:
1 Locate air gap only in spaces with adequate temperature and air movement to absorb ﬂ ash steam, or condensing on nearby surfaces my occur.

Refer to governing codes for drain pipe size and maximum discharge water temperature.

2  Pitch steam hose or tubing toward humidiﬁ er:
  – 2"/ft (15%) when using steam hose
  – ½"/ft (5%) when using 1½" tubing
  – ¼"/ft (2%) when using 2" tubing
3  Dashed lines indicate provided by installer

DC-1046a

OM-351c

Secure and seal
escutcheon plates

Table 44-1:
Dispersion tube and condensate drain escutcheon plate dimensions

for 1½" tube

for 2" tube

inches

1.51

2.03

3.25

5.00

127

0.75

3.25

A
(diameter)

C
(diameter)

INSTALLATION

Single tube and multiple tube

Dispersion:

FIGURE 44-1: SINGLE TUBE DISPERSION WITH CONDENSATE WASTED TO FLOOR DRAIN

Steam hose or tubing. Insulate tubing
to reduce steam loss. Do not insulate
steam hose.

FIGURE 44-2: DISPERSION TUBE AND
CONDENSATE DRAIN ESCUTCHEON
PLATES

Dispersion tube

Содержание Vaporstream

















































































Результаты поиска

Содержание Vaporstream

Отзывы:

Похожие инструкции для Vaporstream

Бренды по названию

Популярные бренды

DriSteem Vaporstream, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Vaporstream

Отзывы:

Похожие инструкции для Vaporstream

Бренды по названию

Популярные бренды