Dräger Polytron 7500 Скачать руководство пользователя страница 25

Страница: 25 / 72

9023927 - 2nd edition - May 2007

Page 25 of 72 Pages

Maintenance

Replacing the pump

●

Disable the supply voltage.

●

Remove the cover of the Polytron 7500. To do this

gently pull apart the cover on both sides and

lift upwards.

Replace the pump for the measurement branch

— Pump on the right side infront of the pyrolysis oven.

●

Remove the connector of the pump.

●

Remove the upper holder of the pump from the middle sheet.

●

Remove the hose from the pump and insert it into the new pump at the same
position.

●

Refit the new pump (without blue label) sideways on the lower holder.

●

Insert the upper holder of the pump into the middle sheet and pull it through.

●

Insert the connector of the new pump into the socket on the printed circuit board.

Ensure correct polarity! Blue cable to the outside.

Replace the pump for the principal branch

— Pump on the left side infront of the rear wall.

●

Remove the connector of the pump.

●

Remove the upper holder of the pump from the middle sheet.

●

Remove the hose from the pump and insert it into the new pump at the same
position.

●

Refit the new pump (with blue label) sideways on the lower holder.

●

Insert the upper holder of the pump into the middle sheet and pull it through.

●

Insert the connector of the new pump into the socket on the printed circuit board.

Ensure correct polarity! Blue cable to the outside.

●

Refit the cover of the Polytron 7500.

●

Switch on power supply.

●

Wait until the sensor has fully warmed up.

— The Polytron 7500 is ready for use again.

Attention!
When the unit is opened

there is the danger of scalding yourself on hot

parts of the Polytron 7500.

02923927_1.eps

0302392

7_02_fr

.eps

blue

sans bleu
étiquette

2392

7_02_fr

.eps

bleu

avec bleu
étiquette

Содержание Polytron 7500









































































Результаты поиска

Содержание Polytron 7500

Отзывы:

Похожие инструкции для Polytron 7500

Бренды по названию

Популярные бренды

Dräger Polytron 7500, Инструкция по эксплуатации

Результаты поиска

Содержание Polytron 7500

Отзывы:

Похожие инструкции для Polytron 7500

Бренды по названию

Популярные бренды