Dräger Polytron 7500 Скачать руководство пользователя страница 14

Страница: 14 / 72

Installing accessories

Page 14 of 72 Pages

9023927 - 2nd edition - May 2007

Inserting the relay module into the docking station

●

Remove the cover of the Polytron 7500. To do this

gently pull apart the cover on both sides and

lift upwards.

Insert connector with clip of the relay cable into opening on the back-plate of the
Polytron 7500.

Connect the other end onto the terminal in the measuring unit.

Fix cable with cable tie to the bracket

Push relay housing from below into the docking station until it snaps into place.

●

Insert the Polytron 7500 back into the docking station.

Carry out function test

— Polytron 7500 operates in the measurement mode (normal operation).

The LED on the side of the relay module lights green.

●

Hold the hose briefly until a flow fault is displayed (red LED on the front side of
the Dräger Polytron 7500).

The LED on the side of the relay module lights red.

72392

7_1

.eps

04823927_1.eps

2392

7_1

.eps

Содержание Polytron 7500









































































Результаты поиска

Содержание Polytron 7500

Отзывы:

Похожие инструкции для Polytron 7500

Бренды по названию

Популярные бренды

Dräger Polytron 7500, Инструкция по эксплуатации

Результаты поиска

Содержание Polytron 7500

Отзывы:

Похожие инструкции для Polytron 7500

Бренды по названию

Популярные бренды