Dräger Polytron 7500 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 72

background image

9023927 - 2nd edition - May 2007

Page 39 of 72 Pages

The menu » Calibration «

The menu » Calibration «

The menu » Calibration « contains all functions needed for the calibration and adjust-
ment of the installed sensor.

Overview

Sub-menu » Zero. calibration «

The sub-menu » Zero calibration « contains the functions for calibrating / adjusting
the zero point of the installed sensor.

Zero point calibration / adjustment

The zero point can be calibrated without the use of zero gas when the ambient air is
free from measuring gas and other interfering gases. Alternatively:

●

Provide zero gas with a flow rate of 1.5 L/min via a T-piece to the inlet connection.
Connect a hose with a length of 0.5 m and a diameter which is larger than the
hose for the Polytron 7500 to the third connection of the T-piece.

Calibration procedure (using the DrägerSensor XS NF

3

as an example

)

:

●

Select the menu items » Calibration «, » Zero calibration « and » XS–NF

3

« in this

order, pressing the »

« key after each selection.

— The message » Supply zero gas with flow rate 500 ml/min « is displayed (this flow

rate is not to be observed for the Polytron 7500).

●

Supply zero gas to the sensor.

●

Select » Next « and press the »

« key.

— The current value and the expired time are now displayed.

Information

Calibration

Calibration

Settings

Zero. calibration

Zero calibration

Span calibration

XS–PFC

1)

1)

The sensor shown in this overview serves only as an example and may differ from the actual sensor installed in the unit.

Autocalibration

Span calibration

XS–PFC

1)

Attention! Never release zero gas directly (without T-piece) from a com-
pressed air cylinder!

1.5 L/min

04

1

2392

7_1_en.eps

OK

OK

«
...
37
38
39
40
41
...
»

Содержание Polytron 7500









































































Отзывы:

Нет отзывов

Похожие инструкции для Polytron 7500

Бренд: dacell Страницы: 22

Бренд: OHAUS Страницы: 19

Бренд: OHAUS Страницы: 54

Бренд: Zenner Страницы: 2

Бренд: Saluki Страницы: 312

Бренд: Vectronics Страницы: 4

Бренд: Polimaster Страницы: 6

Бренд: STONEX Страницы: 99

Бренд: Victron energy Страницы: 46

Бренд: Omega Страницы: 20

Бренд: Banner Страницы: 4

Бренд: Hanna Instruments Страницы: 21

Бренд: Ralcam Страницы: 8

Бренд: TE Connectivity Страницы: 5

Бренд: Voweek Страницы: 20

Бренд: HACH LANGE Страницы: 140

Eniscope Hybrid

Бренд: Best.Energy Страницы: 52

Бренд: LMI Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды